Chapter 4 Powering On Cisco IAD2430 Series IADs

Initial Configuration Procedures

Setup Command Facility

The setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system. Use the setup command facility to configure a hostname for the router, to set passwords, and to configure an interface for communication with the management network.

To use the setup command facility, you will need to set up a console connection with the router and enter the privileged EXEC mode.

To configure the initial router settings by using the setup command facility, follow these steps:

Step 1 Set up a console connection to your router, and enter privileged EXEC mode. For instructions on how to enter privileged EXEC mode see Step 1 through Step 4 in the “Cisco IOS CLI” section on page 4-3.

Step 2 In privileged EXEC mode, at the prompt, enter setup.

yourname# setup

The following message is displayed:

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]:

You are now in the setup command facility.

The prompts in the setup command facility vary, depending on your router model, on the installed interface modules, and on the software image. The following steps and the user entries (in bold) are shown as examples only.

Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. Press Ctrl-C, and enter the setup command at the privileged EXEC mode prompt (Router#).

Step 3 To proceed by using the setup command facility, enter yes:

Continue with configuration dialog? [yes/no]: yes

Step 4 When the following messages appear, enter yes to enter basic management setup:

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: yes

Step 5 Enter a hostname for the router (this example uses Router):

Configuring global parameters:

Enter host name [Router]: Router

Step 6 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration.

The enable secret is a password used to protect access to

Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide

4-4

OL-4234-06

 

 

Page 75 Page 77
Page 76
Image 76
Cisco Systems IAD2430 manual Setup Command Facility
Page 75 Page 77

IAD2430 specifications

Cisco Systems IAD2430 is a versatile Integrated Access Device (IAD) designed to deliver voice and data services to small and medium-sized businesses. This device plays a pivotal role in the convergence of voice and data networks, offering a comprehensive solution that simplifies management and enhances operational efficiency.

One of the most compelling features of the IAD2430 is its support for both traditional TDM (Time-Division Multiplexing) and VoIP (Voice over Internet Protocol) technologies. This dual capability enables businesses to migrate to IP-based voice solutions while still maintaining their existing TDM infrastructure. The IAD2430 is equipped with multiple built-in voice ports, allowing it to support a variety of telephony applications.

In terms of performance, the IAD2430 offers robust Quality of Service (QoS) features that prioritize voice traffic to maintain call clarity and reliability. This is particularly critical in environments where voice communication is essential for daily operations. QoS mechanisms ensure that voice packets are transmitted with minimal latency, jitter, and packet loss, providing an uninterrupted communication experience.

The IAD2430 also boasts advanced security features, including firewall protection and encrypted data transmission. This is particularly important for businesses looking to protect sensitive information and ensure compliance with industry regulations. The built-in security measures help safeguard against unauthorized access and potential threats, providing peace of mind to users.

Moreover, the device supports various WAN connections, including T1, DSL, and Ethernet, making it adaptable to different network environments. Its flexible connectivity options allow for seamless integration with existing network infrastructure while maximizing bandwidth utilization.

Management and configuration of the IAD2430 are simplified through a user-friendly web interface and support for remote administration. This allows IT staff to efficiently configure and monitor the device without the need for onsite visits, thus reducing operational costs.

In summary, the Cisco Systems IAD2430 stands out as a reliable and feature-rich IAD capable of catering to the needs of businesses that require integrated voice and data services. Its combination of TDM and VoIP support, enhanced QoS, robust security features, and flexible connectivity options make it an ideal choice for organizations looking to streamline their communication solutions.
Top Page Image Contents