Cisco Systems ME 6500 B

B-1

Cisoc ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

APPENDIX

SFP Transceiver Specifications

This appendix provides cabling specifications for the SFP transceivers supported on the Cisco ME 6500

Ethernet switch. Figure B-1 shows an optical SFP transceiver with the major features labeled. Figure B-2

shows an SFP transceiver that uses Category 5, 5e, 6, or 6a copper network interface cable.

Note Each port must match the wavelength specifications on the other end of the cable. For reliable

communications, the cable must not exceed the required cable length.

Figure B-1 SFP Transceiver (Optical)

Figure B-2 SFP Transceiver (GLC-T)

130927

GLC-SX-MM

Class

1 21CFR1040.10

LN#50 7/01 03-13

S/N: OH1233456

Receive optical bore

Transmit optical bore

Bail clasp

Dust plug

87922

Contents

Main Page CONTENTS Page Page Page Preface Audience Organization Conventions ix Warnings use the following conventions: Statement 1071Warning Definition x xi xii Page Related Documentation Obtaining Documentation and Submitting a Service Request Page 1-1 Product Overview This chapter describes the Cisco ME 6500 series Ethernet switches and contains these sections: Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Figure 1-1 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S)Front View Page Page Page Page Page 1-7 Chapter 1 Product Overview Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Figure 1-3 Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S)Front View Page Page Page Page Page Preparing for Installation Safety 2-2 Site Requirements Temperature and Air Circulation Humidity Altitude Dust and Contamination Corrosion Electromagnetic and Radio Frequency Interference Shock and Vibration System Grounding Preventing Electrostatic Discharge Damage Page Power Requirements Power Connection Guidelines for AC-Powered Systems Power Connection Guidelines for DC-Powered Systems Cabling Requirements Site Preparation Checklist Page Installing the Switch Preparing for Installation Warnings 3-2 3-3 Verifying Package Contents Rack-Mounting 3-5 Chapter 3 Installing the Switch Rack-Mounting Front-mounting position M4 Phillips flat-head screws Attaching L Brackets to the Chassis kit. Note The L brackets are stamped with different part numbers to identify them as left and right. The screw holes. (See Figure 3-1, top view.) o o Installing the Chassis in the Rack 3-7 Chapter 3 Installing the Switch Desk-Top Mounting Front-mounting position Rear-mounting position Desk-Top Mounting chassis. (See Figure 3-3.) o o 12-24 or 10-32 Phillips-head machine screws Installing the System Ground Connecting Source Power to the Chassis Connecting Source DC to the DC-Input Power Supply Connecting Source AC to the AC-Input Power Supply Connecting the Console Port Installing the SFP Transceivers Page Page Powering Up the Chassis Where to Go Next Page Removal and Replacement Procedures Removing and Installing the DC-Input Power Supply Removing the DC-Input Power Supply Page Installing the DC-Input Power Supply Page Removing and Installing the AC-Input Power Supply Removing the AC-Input Power Supply Installing the AC-Input Power Supply Removing and Installing the Fan Tray Removing the Fan Tray Installing the Fan Tray Upgrading the Memory Page Page Page Page APPENDIX A Power Supply Specifications 400 W DC-Input Power Supply Page 400 W AC-Input Power Supply Page 400 W Power Supply AC Power Cords A-6 A-7 A-8 Plug: SEV 1011 Connector: IEC 60320 C13 Cordset rating: 10 A, 250 V Length: 8 ft. 2 in. (2.5 m) APPENDIX B SFP Transceiver Specifications Page Page Page Page Page INDEX Numerics A C D E F G I L O P R S T U W