Manuals / Brands / Communications / IP Phone / Cisco Systems / Communications / IP Phone

Cisco Systems VG202, VG202XM, VG204, VG204XM - page 32

1 52

Download 52 pages, 2.75 Mb

4-4

Cisco VG202, Cisco VG202XM, Cisco VG204, and Cisco VG204XM Voice Gateways Software Configuration Guide

OL-16191-01

Chapter4 Configuring Voice

Auto-Configuration on the Cisco VG202, Cisco VG202XM, CiscoVG204, and Cisco VG204XM Voice Gateways

gateway provisions itself with the CUCM configuration using Skinny Call Control Protocol (SCCP).

Analog ports which have been pre-configured on CUCM automatically register on CUCM as

SCCP-controlled ports.

To provision the voice gateway with auto-configuration when a DHCP server is available, use the

following commands.

SUMMARY STEPS

1. enable

2. configure terminal

3. interface type slot/port

4. ip address dhcp

5. sccp local interface-type interface-number port port-number

6. ccm-manager sccp local interface-type interface-number

7. ccm-manager sccp

8. voice service voip

9. fax protocol t38 [nse[force]]

10. exit

DETAILED STEPS

Command or Action Purpose

Step1 enable

Example:

VG# enable

Enters privileged EXEC mode.

Step2 configure terminal

Example:

VG# configure terminal

Enters global configuration mode. You have entered

global configuration mode when the prompt changes to

VG(config)#.

Step3 interface type slot/port

Example:

VG(config)# interface fastethernet 0/0

Enters interface configuration mode and specifies the

type of interface you plan to configure. You have entered

interface configuration mode when the prompt changes

to VG(config-if)#.

Step4 ip address dhcp

Example:

VG(config-if)# ip address dhcp

Acquires an IP address on an interface from the DHCP.

Step5 sccp local interface-type interface-number port

port-type

Example:

VG(config)# sccp local fastethernet 0/0

Enables SCCP and its related applications (transcoding

and conferencing).

Contents

Main Page CONTENTS Page Preface Document Objectives Audience Documentation Conventions Accessibility Related Documentation Obtaining Documentation and Submitting a Service Request Page Understanding Interface Numbering and Cisco IOS Software Basics About the Voice Gateways Port Numbering Conventions Page Understanding Cisco IOS Software Basics About Cisco IOS Software Getting Help Command Modes Undoing a Command or Feature Saving Configuration Changes Upgrading to a New Cisco IOS Release Typical Voice Gateway Deployment Scenario Where to Go Next Page Page Configuring Your Voice Gateway Using the setup Command About Configuring Your Voice Gateway Preparing to Configure Your Cisco Voice Gateway Using the setup Command 2-3 Step2 When the following message appears, enter yes to begin the initial configuration dialog: Step3 When the following message appears, press Return to see the current interface summary: Step4 Enter a hostname for the voice gateway: 2-4 viewing the configuration: encrypted (less secure) and can be seen when viewing the configuration: ports other than the console port: Step8 Respond to the following prompts as appropriate for your network: Completing the Configuration Page Configuring Your Voice Gateway Using the CLI Configuring the Hostname and Password Verifying the Hostname and Password Configuring Fast Ethernet Interfaces Example Saving Configuration Changes Page Configuring Voice Prerequisites Configuring the Voice Interface Page Auto-Configuration on the Cisco VG202, Cisco VG202XM, Cisco VG204, and Cisco VG204XM Voice Gateways Restriction for Configuring Auto-Configuration Auto-Configuration With a DHCP Server Page Auto-Configuration Without a DHCP Server Page Configuring the Voice Interface for Cisco Unified Communications Manager Page Page Configuring the MAC Address Convention Configuring Calls Call Transfer Call Waiting Three-Party Conferencing Caller ID Page Page APPENDIX A Using the ROM Monitor Entering the ROM Monitor Mode About the ROM Monitor Commands Listing the ROM Monitor Commands Command Descriptions Recovering Boot and System Images Using the Configuration Register About Changing the Configuration Register Changing the Configuration Register Manually Changing the Configuration Register Using Prompts Using the Console Download Function About the Console Download Function Command Description Error Reporting Using Debug Commands Exiting the ROM Monitor Mode INDEX Symbols A B G H I K