Manuals / Brands / Computer Equipment / Switch / Cisco Systems / Computer Equipment / Switch

Cisco Systems 2960, 2960S, 2960S-24TS-S, WSC2960S24TSSRF Connecting to 1000BASE-T SFP

1 94

Download 94 pages, 3.77 Mb

2-23

Catalyst 2960-S Switch Hardware Installation Guide

OL-19732-04

Chapter 2 Switch Installation

Connecting to SFP and SFP+ Modules

Figure 2-24 Connecting to a Fiber-Optic SFP Module Port

Step 3 Insert the other cable end into a fiber-optic receptacle on a target device.

Step 4 Observe the port status LED.

The LED turns green when the switch and the target device have an established link.

The LED turns amber while the STP discovers the network topology and searches for loops. This process

takes about 30 seconds, and then the port LED turns green.

If the LED is off, the target device might not be turned on, there might be a cable problem, or there might

be problem with the adapter installed in the target device. See Chapter 3, “Troubleshooting,” for

solutions to cabling problems.

Step 5 If necessary, reconfigure and restart the switch or target device.

Connecting to 1000BASE-T SFP

Caution To prevent ESD damage, follow your normal board and component handling procedures.

Step 1 Connect one end of the cable to the SFP module port (see Figure 2-25). When connecting to servers,

workstations, and routers, use a four twisted-pair, straight-through cable. When connecting to switches

or repeaters, use a four twisted-pair, crossover cable.

When connecting to a 1000BASE-T device, be sure to use a four twisted-pair, Category 5 or higher cable.

Note The automatic medium-dependent interface crossover (auto-MDIX) feature is enabled by

default. For configuration information for this feature, see the switch software configuration

guide or the switch command reference on Cisco.com.

1LC connector

Catalyst 2960-S

Series

PoE+ 10G

47X

48X

12

206795

1

Contents

Main Page CONTENTS Page Page Page Preface Related Publications Obtaining Documentation and Submitting a Service Request Product Overview Switch Models Front Panel 1-3 Figure 1-2 Catalyst 2960S-48TS-L Front Panel 49 50 SI Figure 1-3 Catalyst 2960S-48TS-S Front Panel 1-4 Figure 1-4 Catalyst 2960S-F48FPS-L Front Panel Catalyst 2960-S 49 51 50 52 210/100 POE+ ports16RJ-45 console port 10/100 PoE+ Ports 10/100/1000 PoE+ Ports 10/100 Ports 10/100/1000 Ports Management Ports USB Type A Port SFP and SFP+ Module Slots Page Page LEDs System LED RPS LED Master LED Port LEDs and Modes Page Page 1-15 Stack LED ETHERNET 740W 2X Figure 1-8 Stack L ED 1Stack member 1 3Stack member 3 2Stack member 2 Console LEDs Ethernet Management Port LED Rear Panel Page FlexStack Ports RPS Connector Cisco RPS 2300 AC Power Connector Management Options Network Configurations Page Switch Installation Preparing Safety Warnings 2-2 2-3 Installation Guidelines Box Contents Tools and Equipment Verifying Switch Operation Planning a Switch Stack Stack Guidelines Page Installing the FlexStack Module Stack Cabling Stack Bandwidth and Partitioning Examples A B C Page Power-On Sequence for Switch Stacks Installing the Switch Rack-Mounting 2-11 Figure 2-10 Rack-Mounting Brackets Attaching the Rack-Mount Brackets 19 inch ETSI 2-12 Chapter 2 Switch Installation Installing the Switch 4Rear-mounting position Figure 2-12 Attaching Brackets for 19-inch Racks 1Front-mounting position 3Mid-mounting position 2Number-8 Phillips flat-head screws (48-0655-01) Mounting in a Rack Figure 2-13 Mounting in a Rack Catalyst 2960-S Series PoE+ 10G Wall-Mounting Attaching the Brackets for Wall-Mounting Attaching the RPS Connector Cover 21 3 Mounting on a Wall Table- or Shelf-Mounting After Switch Installation Connecting the FlexStack Cables Installing the Power Cord Retainer (Optional) 2 3 Installing SFP and SFP+ Modules Installing an SFP or SFP+ Module Removing an SFP or SFP+ Module Connecting to SFP and SFP+ Modules Connecting to Fiber-Optic SFP and SFP+ Modules Connecting to 1000BASE-T SFP 10/100 and 10/100/1000 PoE+ Port Connections Page 10/100 and 10/100/1000 Port Connections Where to Go Next Troubleshooting Diagnosing Problems Switch POST Results Switch LEDs Switch Connections Bad or Damaged Cable Ethernet and Fiber-Optic Cables Link Status 10/100 or 10/100/1000 Port Connections 10/100 or 10/100/1000 PoE Port Connections SFP and SFP+ Module Interface Settings Ping End Device Switch Performance Speed, Duplex, and Autonegotiation Autonegotiation and Network Interface Cards Cabling Distance Clearing the Switch IP Address and Configuration Finding the Switch Serial Number 3-6 3-7 Page Replacing a Failed Stack Member Page A Technical Specifications Page Page Page Page Page B-1 B Connector and Cable Specifications Connector Specifications 10/100 Ports (Including PoE) All the 10/100 ports use standard RJ-45 connectors and Ethernet pinouts. 10/100/1000 Ports (Including PoE) All the 10/100/1000 ports use standard RJ-45 connectors and Ethernet pinouts. Figure B-2 10/100/1000 Port Pinouts SFP Module Connectors Figure B-3 Duplex LC Cable Connector Cables and Adapters SFP Module Cables Page B-5 Cable Pinouts Console Port Adapter Pinouts Page Page C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through Express Setup Accessing the CLI Through the Console Port Connecting the RJ-45 Console Port or USB Console Port Installing the Cisco Microsoft Windows USB Device Driver Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB Driver Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Using the Add or Remove Programs Utility Using the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB Driver Entering the Initial Configuration Information IP Settings Completing the Setup Program Page Page INDEX Numerics A B D E F G L M N O R S T U W