Manuals / Brands / Computer Equipment / Switch / Cisco Systems / Computer Equipment / Switch

Cisco Systems 2960, 2960S, 2960S-24TS-S, WSC2960S24TSSRF Installing the Cisco Microsoft Windows USB Device Driver

1 94

Download 94 pages, 3.77 Mb

C-3

Catalyst 2960-S Switch Hardware Installation Guide

OL-19732-04

Appendix C Configuring the Switch with the CLI-Based Setup Program

Accessing the CLI Through the Console Port

Step 3 Configure the baud rate and character format of the PC or terminal to match the console port default

characteristics:

• 9600 baud

• 8 data bits

• 1 stop bit

• No parity

• None (flow control)

Step 4 Power on the switch as described in the switch getting started guide.

Step 5 The PC or terminal displays the bootloader sequence. Press Enter to display the setup prompt. Follow

the steps in the “Completing the Setup Program” section on page C-6.

Installing the Cisco Microsoft Windows USB Device Driver

A USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the

switch USB console port.

Installing the Cisco Microsoft Windows XP USB Driver

Step 1 Obtain the file Cisco_usbconsole_driver.zip from the Cisco.com web site and unzip it.

Note You can download the driver file from the Cisco.com site where you download the switch

software.

Step 2 If using 32-bit Windows XP, double-click the file setup.exe from the Windows_32 folder. If using 64-bit

Windows XP, double-click the file setup(x64).exe from the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins.

Step 4 The Ready to Install the Program window appears, Click Install.

Step 5 The InstallShield Wizard Completed window appears. Click Finish.

Step 6 Connect the USB cable to the PC and switch console port. The LED for the USB console port turns green

(see Table 1-10), and within a few seconds a series of Found New Hardware Wizard windows appear.

Follow the instructions to complete the driver installation.

The USB console is ready for use.

Contents

Main Page CONTENTS Page Page Page Preface Related Publications Obtaining Documentation and Submitting a Service Request Product Overview Switch Models Front Panel 1-3 Figure 1-2 Catalyst 2960S-48TS-L Front Panel 49 50 SI Figure 1-3 Catalyst 2960S-48TS-S Front Panel 1-4 Figure 1-4 Catalyst 2960S-F48FPS-L Front Panel Catalyst 2960-S 49 51 50 52 210/100 POE+ ports16RJ-45 console port 10/100 PoE+ Ports 10/100/1000 PoE+ Ports 10/100 Ports 10/100/1000 Ports Management Ports USB Type A Port SFP and SFP+ Module Slots Page Page LEDs System LED RPS LED Master LED Port LEDs and Modes Page Page 1-15 Stack LED ETHERNET 740W 2X Figure 1-8 Stack L ED 1Stack member 1 3Stack member 3 2Stack member 2 Console LEDs Ethernet Management Port LED Rear Panel Page FlexStack Ports RPS Connector Cisco RPS 2300 AC Power Connector Management Options Network Configurations Page Switch Installation Preparing Safety Warnings 2-2 2-3 Installation Guidelines Box Contents Tools and Equipment Verifying Switch Operation Planning a Switch Stack Stack Guidelines Page Installing the FlexStack Module Stack Cabling Stack Bandwidth and Partitioning Examples A B C Page Power-On Sequence for Switch Stacks Installing the Switch Rack-Mounting 2-11 Figure 2-10 Rack-Mounting Brackets Attaching the Rack-Mount Brackets 19 inch ETSI 2-12 Chapter 2 Switch Installation Installing the Switch 4Rear-mounting position Figure 2-12 Attaching Brackets for 19-inch Racks 1Front-mounting position 3Mid-mounting position 2Number-8 Phillips flat-head screws (48-0655-01) Mounting in a Rack Figure 2-13 Mounting in a Rack Catalyst 2960-S Series PoE+ 10G Wall-Mounting Attaching the Brackets for Wall-Mounting Attaching the RPS Connector Cover 21 3 Mounting on a Wall Table- or Shelf-Mounting After Switch Installation Connecting the FlexStack Cables Installing the Power Cord Retainer (Optional) 2 3 Installing SFP and SFP+ Modules Installing an SFP or SFP+ Module Removing an SFP or SFP+ Module Connecting to SFP and SFP+ Modules Connecting to Fiber-Optic SFP and SFP+ Modules Connecting to 1000BASE-T SFP 10/100 and 10/100/1000 PoE+ Port Connections Page 10/100 and 10/100/1000 Port Connections Where to Go Next Troubleshooting Diagnosing Problems Switch POST Results Switch LEDs Switch Connections Bad or Damaged Cable Ethernet and Fiber-Optic Cables Link Status 10/100 or 10/100/1000 Port Connections 10/100 or 10/100/1000 PoE Port Connections SFP and SFP+ Module Interface Settings Ping End Device Switch Performance Speed, Duplex, and Autonegotiation Autonegotiation and Network Interface Cards Cabling Distance Clearing the Switch IP Address and Configuration Finding the Switch Serial Number 3-6 3-7 Page Replacing a Failed Stack Member Page A Technical Specifications Page Page Page Page Page B-1 B Connector and Cable Specifications Connector Specifications 10/100 Ports (Including PoE) All the 10/100 ports use standard RJ-45 connectors and Ethernet pinouts. 10/100/1000 Ports (Including PoE) All the 10/100/1000 ports use standard RJ-45 connectors and Ethernet pinouts. Figure B-2 10/100/1000 Port Pinouts SFP Module Connectors Figure B-3 Duplex LC Cable Connector Cables and Adapters SFP Module Cables Page B-5 Cable Pinouts Console Port Adapter Pinouts Page Page C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through Express Setup Accessing the CLI Through the Console Port Connecting the RJ-45 Console Port or USB Console Port Installing the Cisco Microsoft Windows USB Device Driver Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB Driver Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Using the Add or Remove Programs Utility Using the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB Driver Entering the Initial Configuration Information IP Settings Completing the Setup Program Page Page INDEX Numerics A B D E F G L M N O R S T U W