Cisco Systems 4500 E-Series, WSUPOE12VPSPL - page 19

1-3

Catalyst 4500 E-Series Switches Installation Guide

OL-13972-01

Chapter 1 Product Overview

Switch Features

Table 1-1 describes the features of the Catalys t 4503-E switch.

Tab l e 1-1 Features of the Catalyst 4503 Switch

Feature Description

Ethernet speeds • Ethernet (10BASE-T) interface to workstations and repeaters

• Fast Ethernet (100BASE-T) interface to workstations, servers, switches,

and routers

Note Autonegotiation of link speed on each 10/100 port allows migration to

100BASE-T from a 10BASE-T installed base.

• Gigabit Ethernet (1000BASE-T and 1000BASE-X) interfaces for

backbone interconnection of high-performance workstations, servers,

switches and routers

• 10-Gigabit Ethernet interfaces for backbone interconnection of

high-performance switches and routers

Standard equipment • Three-slot modular chassis with one slot reserved for a supervisor engine

and two slots for switching modules

• One hot-swappable fan assembly

• Two power supply bays

Power supplies • Supports a 1000 W, 1300 W, 1400 W, 2800 W, or 4200W AC-input power

supply or a 1400 W DC-input single input or triple-input power supply1

• Optional redundant power supply

Supervisor engine

support

• Supports the WS-X4013+, WS-X4013+TS, WS-X4013+10GE,

WS-X4515, WS-X4516, WS-X4516-10GE, and WS-X45-Sup6-E

supervisor engines

• Holds the ASIC-based forwarding engine (data path) and the management

processor and software (control path)

• Features interface monitoring, environmental status, and SNMP and

console/Telnet interface

Note Packets are not forwarded while the module is removed; a system

reboot occurs when a supervisor engine is reinserted.

Switching module

support

• 24-port 10/100BASE-TX Fast Ethernet switching module

(WS-X4124-RJ45)

• 24-port 100BASE-FX Fast Ethernet switching module

(WS-X4124-FX-MT)

• 48-port 100BASE-FX Fast Ethernet switching module

(WS-X4148-FX-MT)

• 48-port 100BASE-LX10 Fast Ethernet switching module

(WS-X4148-FE-LX-MT)

• 48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ)

• 48-port 100BASE-BX10-D Fast Ethernet switching module

(WS-X4148-FE-BD-LC)

• 48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ21)

Contents

Main Page CONTENTS Page Page Page Preface Audience Organization Related Documentation Conventions Page x Warnings use the following conventions: xi Page xiii Page Obtaining Documentation and Submitting a Service Request Page Product Overview Switch Features Power Redundancy Catalyst 4503-E Switch Features Page Page Catalyst 4506-E Switch Features Page Page Supervisor Engine Redundancy Catalyst 4507R-E Switch Features Page Page Page 1-13 Catalyst 4500 E-Series Switches Installation Guide OL-13972-01 Chapter 1 Product Overview Switch Features Catalyst 4510R-E Switch Features Figure 1-4 Catalyst 4510R-E Switch (Front View) ST A TUS Page Page Supervisor Engines Page Page Page Page Page LEDs Gigabit Ethernet Uplink Ports 10-Gigabit Ethernet Uplink Ports SFP Ports 10/100BASE-T Management Port CONSOLE Port RESET Button Fan Assembly Power Supplies Page Page Power Supply LEDs Power Supply Fan Load-Sharing Feature Environmental Monitoring Feature 1400 W DC Triple-input Power Supply Operational Modes Page System Architecture Power Flow Power over Ethernet PoE Over-subscription PoE Switching Modules Deploying PoE on the Cisco Catalyst 4500 E-series Cisco Catalyst 4500 Series Service Provider DC Power Supply Management Flow Switching Traffic Flow Over-subscription Supervisor Redundancy Page Preparing for Installation Electrostatic Discharge Preventing Electrostatic Discharge Damage Site Power Requirements and Heat Dissipation Power Connection Guidelines for AC-Powered Systems Page Page Page Page Page Power Connection Guidelines for DC-Powered Systems Calculating DC Input Current Ventilation Calculating System Heat Dissipation Site-Planning Checklist Page Installing the Switch in a Rack Checking the Shipping Container Contents Rack-Mounting the Switch Required Installation Tools Rack-Mounting Catalyst 4500 E-series Switches Page System Ground Connection Guidelines Parts and Required Tools Connecting System Ground and Power Page Page Removing and Replacing FRUs Removing and Replacing the Power Supply 4-3 Required Tools Removing an AC-Input Power Supply Page Installing an AC-Input Power Supply Page Removing a DC-Input Power Supply Required Tools Removal Procedure 4-9 Figure 4-13 or Figure 4-14). Statement 1046 4-10 Installing a DC-Input Power Supply Required Tools Installation Procedure Removing and Replacing the Chassis Fan Assembly Required Tools Removing the Fan Assembly Installing the Fan Assembly Verifying the Installation Replacing Backplane Modules Page Page Verify the New Modules Supervisor Memory Upgrade Tools and Equipment Needed Removing Memory Page Installing SDRAM MiniDIMMs Page Troubleshooting System Boot Verification Using LEDs to Identify Startup Problems Page System Messages Troubleshooting with Software Troubleshooting the Power Supply System Messages and Power Problems Power Supply Mixing Troubleshooting the Fan Assembly System Messages and Fan Problems Troubleshooting Backplane Modules Troubleshooting Switching Modules System Messages and Switching Modules Troubleshooting Supervisor Engines System Messages and Supervisor Engines Page Standby Supervisor Engine Problems Switch Self-reset Ports 1/2 and 2/2 Do Not Function Packet Loss Some Problems and Solutions Module Not Online Interface Problems Workstation Is Unable to Log In to the Network NIC Compatibility Issues Interface Is in Errdisable Faulty Supervisor Engine Boot Problems Cannot Connect to a Switch Through the Console Port Cannot autonegotiate the port speed/duplex Contacting the Cisco Technical Assistance Center Serial Numbers Page A Specifications Catalyst 4503-E Switch Specifications Catalyst 4506-E Switch Specifications Catalyst 4507R-E Switch Specifications Page Catalyst 4510R-E Switch Specifications Catalyst 4500 Power Supplies Page Page Page Page Page Page Page Page B Repacking a Switch B-2 C Initial Configuration for the Switch Connecting to the Switch Starting the Terminal-Emulation Software Connecting to a Power Source Entering the Initial Configuration Information IP Settings Performing the Initial Configuration Page Page Page D Module Overview and Specifications Catalyst 4500 Series Switches Catalyst 4500 E-Series Switches Supervisor Engines Page Front-Panel Components Ethernet Management Port Console Port Supervisor Memory Switching Modules WS-X4606-X2-E WS-X4648-RJ45V-E WS-X4648-RJ45V+E Switching Module LEDs Hot-Swapping Feature INDEX Numerics A B D E F G H I L M O P S T U V