2Printer Operation
Mode Settings
[Zebra® Emulation]
Top Menu | Sub Menu | Default | Menu | Remarks |
|
|
|
|
|
After Print | AutoConfigure | On | On | Optional auto configure |
|
|
| Off | On .... Auto configure effective. |
|
|
|
| If a peeler unit or |
|
|
|
| installed, each mode is automatically |
|
|
|
| set regardless of the “function select” |
|
|
|
| setting. |
|
|
|
| Off ... Auto configure ineffective. |
|
|
|
| When a peeler unit or |
|
|
|
| installed but has not been started, it is |
|
|
|
| off and the operation is selected by |
|
|
|
| “Function select”. |
|
|
|
|
|
| Function Select | Tear | Off | Selects the type of options installed and |
|
|
| Tear | adjusts the "paper stop" position accordingly. |
|
|
| Peel On* | For example, the position where the label |
|
|
| Cut On* | stops in "Tear" mode is different to that in |
|
|
|
| "Peel On" mode. |
|
|
|
|
|
| Cutter Action* | Backfeed | Backfeed | Cutter operating method setting |
|
|
| Through | Backfeed: it feeds back after each cutting |
|
|
|
| operation. |
|
|
|
| Through: when the number copied = n, the |
|
|
|
| back end of sheet 1 to |
|
|
|
| and the back end of the final page that is a |
|
|
|
| single sheet is copied and fed back. |
Paper Position | 0.00IN | Peel/Cut/Tear Off |
| 0.00mm | 0.00 to 2.00 IN |
|
| 0.0 to 50.8mm |
|
| Peel/Cut/Tear On |
|
| |
|
|
The stop position can be fine tuned using this menu setting. The general stop position is selected depending on the "Function" selected above.
| Mode/Repeat Key | Disabled | LabelSet | Repeat method selection |
|
|
| LastOne | LabelSet: |
|
|
| Disabled | Reissues multiple labels. |
|
|
|
| LastOne: |
|
|
|
| Issues only the final page. |
|
|
|
| In count case, it issues only 1 label while |
|
|
|
| continuing. |
|
|
|
| Disabled: |
|
|
|
| Makes the repeat key invalid. |
|
|
|
|
|
Interface | 9600 | 115200 | Sets the baud rate of the serial interface. | |
|
|
| 57600 | • Interface related settings are effective |
|
|
| 38400 | after the power is turned on again. |
|
|
| 19200 |
|
|
|
| 9600 |
|
|
|
| 4800 |
|
|
|
| 2400 |
|
| None | None | Sets the communication parity of the serial | |
|
|
| Odd | interface. |
|
|
| Even |
|
|
|
|
|
|
| 8 bits | 8 bits | Sets the character length of the serial | |
|
|
| 7 bits | interface. |
|
|
|
|
|
| 1 bit | 1 bit | Sets the stop bit of the serial interface. | |
|
|
| 2 bits |
|
|
|
|
|
|
| Yes | Yes | Selects the | |
|
|
| No | interface. |
|
|
|
|
|
| IEEE1284 | ON | ON | Enable or disables the 'enhanced' features of |
|
|
| OFF | the IEEE1284 parallel interface. |
|
|
|
|
|
* Effective only when the optional unit is attached.
36