Clarity XLC 3.4 manual XLC3.4 Battery Information XLC3.4 Placing & Answering Calls, Handset, Loud

XLC3.4 BATTERY INFORMATION

XLC3.4 PLACING & ANSWERING CALLS

HANDSET

The batteries in the handset must be fully charged for 10 hours before using the telephone for the first time.

Battery life: Talk time is 6.5 hours, while standby is 130 hours without usage. Actual times will vary depending on the amplifier settings used. Replace batteries every two years.

Battery spec (as supplied with your phone): 3xAAA NiMH rechargeable batteries,(1.2V 600mAh NiMH, 60AAAHC, GPI International Ltd.).

To replace batteries, remove the handset battery cover and install new batteries, then close battery cover.

BASE (OPTIONAL)

The base batteries are optional (backup). If you choose to install backup batteries for the base, use rechargeable batteries ONLY. The backup batteries should be AAA, NiMH, rechargeable only, rated 600mAh.They must be fully charged for 10 hours before using the telephone for the first time.

The base backup batteries ensure the functionality of your cordless phone (3-4 hours) in case of a power outage.

When the base unit operates in battery mode (no AC power). the base POWER light will blink once every two seconds.

Open battery compartment door here.

To install batteries in the base:

1.Turn base over and open battery compartment door.

2.Install batteries according to the polarity shown inside the battery compartment.

NOTE:To replace handset batteries or to install base backup batteries, use ONLY standard rechargeable AAA NiMH batteries - 600mAh.

LOW BATTERY INFORMATION

Handset

1.The battery icon on the screen shows no bars; the screen displays “Low Battery”.

2.The handset beeps every two seconds in OFF HOOK mode.

3.The TALK button blinks green twice every 15 seconds in standby mode. It will not flash an alert in OFF HOOK mode.

Base (if optional batteries are installed)

1.The POWER light will blink green once every five seconds.

WARNING: Use rechargeable batteries only.

Do NOT use alkaline batteries!

TO PLACE A CALL:

1.Press TALK, then dial the number using the numeric keypad. See lighting pattern for the TALK button on the bottom of the page.

2.Adjust the volume to the most comfortable level - using the Volume Control and BOOST button (if necessary).

3.Press the TONE button on the side of the handset to adjust the tonality of the incoming voice to the most comfortable level.

WARNING:VOLUME MAY BE

LOUD!

NOTE:

1.If the Voice Assist function is enabled, you will hear the digits of the incoming phone number.

2.Step 1 above can be replaced with one of the following options:

•Dial from CID records: Choose a record from your Caller List (see page 17), then press TALK.

•Dial from PHONEBOOK: Choose a record from your Phonebook (see page 18), then press TALK.

•Pre-dial: before pressing TALK, dial the number you wish to call; digits will display on the screen; press TALK when the number is complete.

Follow with steps 2-3 above to enjoy a clear and comfortable phone conversation.

TO ANSWER A CALL:

1.When phone is ringing, press TALK to answer the call.

2.Adjust the volume and tone of the incoming voice according to your preferences.

3.When finished, press TALK to hang up.

NOTE:

1.For an explanation of the TALK button light, see the bottom of the page.

2.If you have CID service, note the incoming phone number displayed on your screen.

3.If the Voice Assist function is enabled, you will hear the digits of the incoming phone number.

4.At any point during the conversation, press the

speakerphone button  to switch to handsfree mode. Use the volume control for adjusting the level of the incoming audio. Switch back to earpiece mode by pressing the speakerphone button again.

Talk Button Lighting Pattern

Green: Phone is in use.

Flashing Green every 15 seconds in standby mode: Low batteries.

E

N G L I S H

14 15