Operating Your Radio
Speaker/Mic Port
Talk Button
Backlight/Key Lock Button
Key Locked Buttons
| R | ROG GMRS |
| VHF | |
| T X |
|
| A |
|
| B U I C | |
ATIS VOX LOMEDHISAMEMEM | ||
FLOATING | MARINE HH350 | |
| CALL |
|
|
TW | ENT SETUP | 16/9 | |
MEM |
| ||
|
|
| |
SCAN | ESC |
| WX |
| H M L | ||
SUBMERSIBLE
Key Lock Icon
GMRS VHF
14 English
Getting Started
Radio Speaker and Microphone
The internal Radio Speaker and Microphone are located on the bottom front face of the radio below the lower control buttons.
An optional Speaker/Microphone port is located at the top of the radio between the antenna and the Power/Volume control. Unthread the Speaker/Microphone port cover to access and install an optional Cobra speaker or microphone into this port.
Talk Button
Press and hold the Talk button to transmit messages. Release the Talk button to stop transmitting.
Backlight/Key Lock Button
To Display the Backlight Momentarily:
Press the Backlight/Key Lock button. The backlight will remain On for 10 seconds. If the backlight is already On, another press of the Backlight/Key Lock button will turn it Off.
Key Lock
To prevent accidental changes to your settings, you can lock all of the following buttons:
■Channel Up Button
■Channel Down Button
■SCAN Button
■MEM/ESC Button
■WX/H-M-L Button
■16/9 Button
■
■Call/Enter/Setup Button
To Lock or Unlock the Buttons:
Press and hold the Backlight/Key Lock button for two
(2)seconds. The Key Lock icon will appear or disappear in the LCD. When Key Lock is On, pressing any of the listed buttons on the front of the radio will result in a three (3) beep error message.
Both the Backlight/Key Lock button and the Talk button are active — you can Receive (Rx) or Transmit (Tx)
a message with Key Lock On, but you cannot change the channel.
Operating Your Radio
Channel Up/Down Buttons
FLOATING | MARINE HH350 |
| ||
|
|
|
|
|
CALL
ENT
SETUP
Currently On Channel 88
TRX
A
B U I C ATIS VOX LOMEDHISAM
SCAN Button
MEM
ESC
SCAN
Getting Started
Channel Up/Down Buttons
Your radio will Receive (Rx) and Transmit (Tx) VHF signals on the channel indicated on the LCD display. You can change the channel at any time using the Channel Up/Down buttons.
To Change Channels:
Press the Channel Up/Down button.
If you are on Channel 88, pressing the Channel Up button will advance to Channel 01. If you are on Channel 01, pressing the Channel Down button will advance to Channel 88.
You can press and hold the Channel Up/Down button for fast advance. The beep sound will occur only at the first press of the button and not during fast advance.
If the new channel selected is restricted to low power, the radio will automatically switch to Low Power mode and the Low Power icon will appear on the LCD.
If the radio is in the Key Lock mode, the channel will not change and the three (3) beep error signal will sound.
SCAN Button
Press and release the SCAN button to scan all channels. The SCAN icon will display on the LCD display. Scanning begins at lower channels, and scans to higher channels. Press the Channel Up/Down button to change the scan direction.
When a signal is received in SCAN mode, the radio will pause 10 seconds before resuming SCAN operation. The scan will stop on the paused channel and remain there when the Talk button is pressed.
In Memory mode, press and release the SCAN button to scan all memory channels. Because the unit is already in the Memory Channel mode, only the channels in the memory bank will be displayed.
NOTE
Memory channels need to be saved to effectively enter the Memory Channel mode and scan all memory channels.
Nothing Comes Close to a Cobra® 15
