SAFETY mNSTRUCTmONS FOR BASmC SAW OPERATmON

BEFORE USING THE MITER SAW

IAWARNINGn

To avoid mistakes thatcould cause serious,

permanent injury, do not plug the toolin until the following steps are completed:

,Completely assemble and adjust the sew, following the instructions. (ASSEMBLY AND ADJUSTMENTS)

,Learn the use and function of the ON/OFF switch, lock-off switch, upper and lower blade guards,

stop latch, bevel lock handle, end cover plate

screws.

,Review and understand all safety instructions and operating procedures in this Operator's Manual (SAFETY & OPERATIONS)

,Reviewthe MAINTENANCE and TROUBLESHOOTING GUIDE for your miter saw.

,To avoid injury or possible death from etectricaJ shock:

Make sure your fingers do not touch the plug's metal prongs when plugging or unplugging your miter saw. (ELECTRICAL REQUIREMENTS AND SAFETY)

BEFORE EACH USE INSPECT YOUR SAW.

Disconnect the miter saw. To avoid injury from accidental starting, unplug the saw before any adjustments, including set-up and blade changes.

,Compare the direction of rotation arrow on the guard to the direction arrow on the blade. The

blade teeth should always point downward st the front of the saw.

,Tighten the arbor bolt.

,Tighten the cover plate screw.

,Check for damaged parts. Check for:

Alignment of moving psAs

Damaged electric cords

Binding of moving parts

,Mounting holes

,Function of arm return spring and lower guard:

Push the cutting arm all the way down, then let it rise until it stops. The lower guard should fully ctose. Follow instructions in TROUBLESHOOTING GUIDE for adjustment if necessary.

,Other conditions that may affect the way the miter saw works.

Keep all guards in place, in working order and proper adjustment. If any part of this miter saw

is missing, bent damaged or broken in any way, or any electrical parts don't work, turn the saw off and unplug it. Replace damaged, missing, or defective parts before using the saw again.

,Maintain tools with care. Keep the miter saw clean for best and safest performance. Follow instructions for lubricating. Don't put lubricants on the blade while it'sspinning.

Remove adjusting wrench from the tool before turning it on.

,To avoid injury from jams, slips, or thrown pieces:

USE ONLY RECOMMENDED ACCESSORIES

Consult the ACCESSORIES and ATTACHMENTS

section of this Operators Manual for recommended accessories. Follow the

instructions that come with the accessory. The use of improper accessories may cause risk of injury to persons.

,Choose the correct 10 inch diameter blade for the

material and the type of cutting you plan to do. Do not use thin kerf blades.

,Make sure the blade is sharp, undamaged and properly aligned. With the saw unplugged, push the cutting arm sH the way down. Manually spin the blade and check for clearance. Tilt the power-

head to s 45° bevel and repeat the test.

Make sure the btede and arbor collars are clean. Make sure all clamps and !ocks ere tight and there is no excessive play in any parts.

KEEPYOUR WORK AREA CLEAN

Cluttered areas and benches invite accidents.

[J& WARNING 1

To avoid burns or other fire damage, never use the miter saw near fmsmmsble Hquids, vapors, or gases.

Plan ahead to protect your eyes, hands, face end

esrs.

,Know your miter saw.

Read and understand the Operator's Manual and labels affixed to the tool Learn its application and limitations as wen as the specific potential hazards peculiar to this tool. To avoid injury from eccidentsJ contact with moving parts, don't do layout, assembly, or setup work on the miter saw while any parts are moving.

,Avoid accidental starting

Make sure the trigger switch is disengaged

before plugging the miter saw into e power outtet.

16

Page 16
Image 16
Craftsman 137.21229 Safety mNSTRUCTmONS for BASmC SAW OPERATmON, Before Using the Miter SAW, Keepyour Work Area Clean