Craftsman 139.53993D owner manual Operation, Using Your Garage Door Opener

OPERATION

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1.READAND FOLLOWALL WARNINGSAND INSTRUCTIONS.

2.ALWAYSkeep remote controls out of reach of children. NEVERpermit children to operate or play with garage door control push buttons or remote controls.

3.ONLYactivate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel.

4.ALWAYSkeep garage door in sight until completely closed.

NOONESHOULDCROSSTHE PATHOFTHE MOVING DOOR.

5.NOONESHOULDGOUNDERA STOPPED,PARTIALLY OPENEDDOOR.

6.If possible, use emergency release handleto disengage trolley ONLYwhen garagedoor is CLOSED.Weak or broken springs or unbalanceddoor could result in an open door failing rapidly and/or unexpectedly.

7.NEVERuse emergency releasehandle unless garage doorway is clear of persons and obstructions.

8.NEVERuse handle to pull garagedoor open or closed. If rope knot becomes untied, you could fall.

Using Your Garage Door Opener

Your Security÷ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Your opener will operate with up to eight Security÷ ® remote controls and one Security÷ ® Keyless Entry System. If you purchase a new remote, or if you wish to deactivate any remote, follow the instructions in the Programming section.

Activate your opener with any of the following:

•The hand-held Remote Control: Hold the large push button down until the door starts to move.

•The wall-mounted Door Control: Hold the push button or bar down until the door starts to move.

•The Keyless Entry (See Accessories): If provided with your garage door opener, it must be programmed before use. See Programming.

When the opener is activated (with the safety reversing sensor correctly installed and aligned)

1.If open, the door will close. If closed, it will open.

2.If closing, the door will reverse.

3.If opening, the door will stop.

4.If the door has been stopped in a partially open position, it will close.

5.If obstructed while closing, the door will reverse. If the obstruction interrupts the sensor beam, the opener lights will blink for five seconds.

9.If one control (force or travel limits) is adjusted, the other control may also need adjustment.

10.After ANY adjustments are made, the safety reversal system MUST betested.

11.Safety reversalsystem MUST betested every month. Garagedoor MUST reverseon contact with 1-1/2" high (3.8 cm) object (or a 2x4 laid flat) on the floor.

12.ALWAYSKEEPGARAGEDOORPROPERLYBALANCED (see page3). An improperly balanced door may not reversewhen required and could result in SEVEREINJURY or DEATH.

13.ALL repairs to cables, spring assemblies and other hardware,all of which are under EXTREMEtension, MUST be made by a trained door systems technician.

14.ALWAYSdisconnect electric power to garage door opener BEFOREmaking ANY repairs or removing covers.

1s.SAVETHESEINSTRUCTIONS.

6.If obstructed while opening, the door will stop.

7.If fully open, the door will not close when the beam is broken. The sensor has no effect in the opening cycle.

If the sensor is not installed, or is misaligned, the door won'tclose from a hand-held remote. However, you can close the door with the Door Control, the Outdoor Key Switch, or Keyless Entry, if you activate them until down

travel is complete. If you release them too soon, the door will reverse.

The opener lights will turn on under the following conditions: when the opener is initially plugged in; when

power is restored after interruption; when the opener is activated.

They will turn off automatically after 4-1/2 minutes or provide constant light when the Light feature on the Premium Control Console Panel is activated. Bulb size is

A19. Bulb power is 100 watts maximum.

Security,I _ light feature: Lights will also turn on when someone walks through the open garage door. With a Premium Control Console, this feature may be turned off as follows: With the opener lights off, press and hold the light button for 10 seconds, until the light goes on, then off again. To restore this feature, start with the opener lights on, then press and hold the light button for 10 seconds until the light goes off, then on again.

30