SAFETY INSTRUCTIONS cont.
ELECTRICAL SAFETY
!WARNING: BE SURE to read and understand all instructions before operating this drill /driver. Failure to follow all instructions listed below may result in electric shock, fire and /or serious personal injury.
A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charging stand/transformer for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.
1.Use battery operated tool only with specifically designated battery pack. Use of any other batteries may create a risk of fire.
2.Use battery only with charging stand / transformer listed.
Kit No. 9 |
|
| |
|
|
|
|
DRILL / DRIVER | CHARGING STAND / TRANSFORMER | BATTERY PACK | |
172.64120 | |||
|
|
| |
| Can also use 1426101 and 140295004 | Can also use 1323509, | |
|
| 1323520, | 130260001, |
|
| 130139020 and 130139021 | |
|
|
|
|
3.Do not abuse the cord on the charging stand. Never carry the charging stand/transformer by its power cord. Never pull the power cord to remove the transformer from the power outlet. Damage to the cord or charging stand/transformer could occur and create an electric shock hazard. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
SAFETY SYMBOLS FOR YOUR TOOL
The label on your tool may include the following symbols.
V | Volts | ||||||
A | Amps | ||||||
Hz | Hertz | ||||||
W | Watts | ||||||
|
|
| .................................................................... |
| Alternating current | ||
|
|
|
|
| ................................................................. | Direct current | |
|
|
|
|
|
| ||
no | |||||||
|
|
| .................................................................... |
| Class II construction, Double Insulated | ||
RPM……........................………………… . . . | Revolutions per minute | ||||||
SPM……..........................…………………....Strokes per minute
OPM………........................………………......Orbits per minute
! | .....................................................................Indicates danger, warning or caution. |
| It means attention! Your safety is involved. |
SERVICE SAFETY
1.If any part of this cordless drill / driver is missing or should break, bend, or fail in any way; or should any component fail to perform properly: have the missing, damaged or failed parts replaced BEFORE resuming operation.
6
SAFETY INSTRUCTIONS cont.
SERVICE SAFETY cont.
2.Tool service must be performed only at a Sears Parts and Repair Center. Service or maintenance performed by unqualified personnel could result in a risk of injury.
3.When servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES FOR CORDLESS DRILL / DRIVERS
1.Know your cordless drill / driver. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.
2.BE SURE that twist drill bits, screwdriver bits and other accessory attachments are properly and securely mounted in the chuck jaws BEFORE operating the drill / driver.
3.ALWAYS carefully inspect the material you are going to drill / drive into. Drilling /driving into nails, pipes and electrical wires can cause serious personal injury.
4.HOLD DRILL / DRIVER by insulated gripping surfaces (handles) when performing an operation where the tool may drill / drive into hidden wiring. Contact with a “live” wire will make the exposed metal parts of the tool “live” and shock the operator.
5.NEVER hold the piece being drilled in your hands or across your legs.
It is important to support and clamp the workpiece properly in order to minimize body exposure, bit binding, or loss of control.
6.Maintain a firm grip on the drill / driver to resist starting torque.
7.Use sharp accessory bits only. For drilling in WOOD use twist drill bits, spade bits, or power auger bits. For METAL use
8.BE SURE the material to be drilled is stationary, anchored or clamped firmly. If drilling thin material, use a
9.ONLY USE the specifically listed battery pack and charging stand listed on page 6 of this manual. Use of any other battery pack or charging stand / transformer can create risk of injury and fire.
10.Cordless tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery operated tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.
11.Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possible injury.
12.Do not crush, drop or damage battery pack. Never use a battery pack or charging stand/transformer that has been dropped or received a sharp blow. A damaged battery pack is subject to explosion. Properly dispose of a dropped or damaged battery pack immediately.
7
