Korea MIC certification | Force10 Networks E1200i manual

commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment. .

Attention: This is a Class A product. In a domestic environment, this device may cause radio interference, in which case, the user may be required to take adequate measures.

European Community Contact

Force10 Networks, EMEA - Central Dahlienweg 19

66265 Heusweiler Germany http://www.force10networks.com/german/ Tel: +49 172 6802630

Email: EMEA Central Sales

Japan: VCCI Compliance for Class A Equipment

This is Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Danger: AC Power cords are for use with Force10 Networks equipment only. Do not use Force10 Networks AC power cords with any unauthorized hardware.

Korea (MIC certification)

Safety Standards and Compliance Agency Certifications

•CUS UL 60950-1, 1st Edition

•CSA 60950-1-03, 1st Edition

•EN 60950-1, 1st Edition

Installing and Maintaining the E1200i System

95

Image 95

Force10 Networks E1200i Safety Standards and Compliance Agency Certifications, Japan Vcci Compliance for Class a Equipment

Contents

Installing and Maintaining the E1200i System Copyright 2008 Force10 Networks Contents Installing Fan Trays Appendix B System Boot Index List of Figures Page List of Tables Page Symbol Description Defines the information symbols used throughout this guide Related Publications Operating Overview E1200i SystemPage Page RPM Component Minimum Maximum Field-Replaceable Step Task Section Supplying Power DC on Site Selection Criteria Chapter Site Preparation Rack Mounting Cabinet PlacementPower Fans and Airflow Storing Components Unpacking the E1200i AC System Installing the AC Chassis Step Task Installing the Equipment Rack Shelf BarTo install a equipment rack shelf bar Standard Front Chassis Mounting To install the chassis into a prepared rack Installing the Chassis into an Equipment Cabinet Installing the AC Chassis Unpacking the E1200i DC System Installing the DC Chassis Installing the DC Chassis Rack-Mounting the Chassis Installing the DC Chassis Installing Fan Trays Screw latch Installing Fan Trays Location To install fan traysIs an illustration of the fan tray safety labels Label Installing Fan Trays On/Standby Switch Installing AC Power Supplies Securing the Chassis Ground Installing Power Supplies Insert power supply AC Power Supply and Fan Operability Test Status LED is Step Task Status Installing AC Power Supplies PEM 0 and PEM 1 Chassis Locations Installing DC Power Supplies Installing DC PEMs Cable and Connector Requirements Use the following steps to install a DC PEM Over current protector PEM interlock lever Locking screws Cable Connector Required for E1200i DC PEM DC PEM with Connections in Place DC Power Supply and Fan Operability Test Step Task Important Points to Remember Installing RPMs, Line Cards SFMsUnpacking an RPM or Line Card Line Cards Installing Line Cards and RPMsRPMs Blank Panels Preparing and Installing RPMs and Line Cards Installing an RPM into the E1200i To install line cards and RPMs Section Label Description Installing a Second RPMRPM Label and LEDs Describes the RPM LED states and the RPM front panel Installing Switch Fabric Modules SFMs Illustrates the SFM front panel and LEDs SFM Front Panel and LEDs Line Card Cable Management Systems RPM Ports Connecting the Console and Auxiliary PortsRPM Ports and Cables Cable and Adapter Pin Assignments Pin Signal Input/Output Accessing the Console with a DB-25 Adapter Accessing the Console with a DB-9 Adapter Label Description Accessing the 10/100 Ethernet Management PortAccessing the Auxiliary Port by Modem Preparation Chapter Powering Up Supplying Power DC Supplying Power AC Booting from the Bootuser Prompt Booting to the CLI Prompt Powering Up Removing and Replacing Fan Trays Removing and Replacing Components Removing and Replacing Components Removing and Replacing AC Power Supplies Installing and Maintaining the E1200i System Remove an AC Power Supply in a redundant installation Removing and Replacing DC Power SuppliesRemove an AC Power Supply in a non-redundant installation Installing and Maintaining the E1200i System Remove a DC Power Supply To remove and replace E1200i line card or RPM modules Removing and Replacing RPMs, Line Cards, or SFMsRemoving and Replacing line cards or RPMs No linecard Removing and Replacing SFMsTo remove and replace an SFM To remove and replace the air filter Removing and Replacing the Air Filter Removing and Replacing Components Inserting the External Flash Memory Card Appendix a Using a Flash Memory CardExternal Flash Memory Card Overview To remove the flash memory card To install the flash memory cardRemoving the External Flash Memory Card Formatting an External Flash Card Displaying Files Stored on the External Flash Command Syntax Command Mode PurposeCopying Files to the External Flash Page Booting from the Bootuser Prompt System Boot Process Step Command To configure the chassis from the Bootuser prompt Step Command Task Show boot selector Show bootvar Port View the Management interface’s physical settingsAuto-negotiation Show default-gateway Default-gateway ip-address Step CommandTask Reload System Boot Appendix C Alarms Power Supplies and Alarms SFMs and Alarms Alarms This appendix contains two major sections Appendix D System SpecificationsE1200i AC System Power Requirements E1200i AC Chassis Physical Design System Specifications E1200i DC Chassis Physical Design E1200i DC System Power Requirements Non-operating Environmental SpecificationsOperating Specifications Agency Compliance Korea MIC certification Safety Standards and Compliance Agency CertificationsJapan Vcci Compliance for Class a Equipment Product Recycling and Disposal Electromagnetic EmissionsImmunity European Weee symbol System Specifications This appendix contains these major sections Appendix E Technical Support Support Policies section of iSupport Accessing iSupport Services Console captures showing the troubleshooting steps taken Output from the show tech-supportnon-paged command ThisOutput from the show logging eventlog unit command, where Console captures showing the error messages To request replacement hardware, follow these steps Requesting a Hardware Replacement FPC Asic Index 104 Index Installing and Maintaining the E1200i System 105