To install fan trays, Label, Location | Force10 Networks E1200i

To install fan trays:

Step Task

1.Unpack the fan tray.

2.Prior to inserting a fan tray, fully turn its screw latch counter-clockwise (with flathead screwdriver) until the fan tray latching mechanism fully retracts into the fan tray (see Figure 10).

3.Grip the fan tray handle. Slide the connector end of each fan tray into the slot until it stops and the handle end is flush with the chassis rear.

4.Secure the fan trays into place by turning the screw latch clockwise.

Table 3 is an illustration of the fan tray safety labels:

Table 3 Fan Tray Safety Labels

Label

FN00051A

Location

Fan tray faceplate

Installing and Maintaining the E1200i System

33

Image 33

Force10 Networks E1200i manual To install fan trays, Is an illustration of the fan tray safety labels, Label, Location

Contents

Installing and Maintaining the E1200i System Copyright 2008 Force10 Networks Contents Installing Fan Trays Appendix B System Boot Index List of Figures Page List of Tables Page Symbol Description Defines the information symbols used throughout this guide Related Publications Operating Overview E1200i SystemPage Page RPM Component Minimum Maximum Field-Replaceable Step Task Section Supplying Power DC on Site Selection Criteria Chapter Site Preparation Cabinet Placement PowerRack Mounting Fans and Airflow Storing Components Unpacking the E1200i AC System Installing the AC Chassis To install a equipment rack shelf bar Installing the Equipment Rack Shelf BarStandard Front Chassis Mounting Step Task To install the chassis into a prepared rack Installing the Chassis into an Equipment Cabinet Installing the AC Chassis Unpacking the E1200i DC System Installing the DC Chassis Installing the DC Chassis Rack-Mounting the Chassis Installing the DC Chassis Installing Fan Trays Screw latch Installing Fan Trays Is an illustration of the fan tray safety labels To install fan traysLabel Location Installing Fan Trays On/Standby Switch Installing AC Power Supplies Securing the Chassis Ground Installing Power Supplies Insert power supply AC Power Supply and Fan Operability Test Status LED is Step Task Status Installing AC Power Supplies PEM 0 and PEM 1 Chassis Locations Installing DC Power Supplies Installing DC PEMs Cable and Connector Requirements Use the following steps to install a DC PEM Over current protector PEM interlock lever Locking screws Cable Connector Required for E1200i DC PEM DC PEM with Connections in Place DC Power Supply and Fan Operability Test Step Task Installing RPMs, Line Cards SFMs Unpacking an RPM or Line CardImportant Points to Remember Installing Line Cards and RPMs RPMsLine Cards Blank Panels Preparing and Installing RPMs and Line Cards Installing an RPM into the E1200i To install line cards and RPMs RPM Label and LEDs Installing a Second RPMDescribes the RPM LED states and the RPM front panel Section Label Description Installing Switch Fabric Modules SFMs Illustrates the SFM front panel and LEDs SFM Front Panel and LEDs Line Card Cable Management Systems Connecting the Console and Auxiliary Ports RPM Ports and CablesRPM Ports Cable and Adapter Pin Assignments Pin Signal Input/Output Accessing the Console with a DB-25 Adapter Accessing the Console with a DB-9 Adapter Accessing the 10/100 Ethernet Management Port Accessing the Auxiliary Port by ModemLabel Description Preparation Chapter Powering Up Supplying Power DC Supplying Power AC Booting from the Bootuser Prompt Booting to the CLI Prompt Powering Up Removing and Replacing Fan Trays Removing and Replacing Components Removing and Replacing Components Removing and Replacing AC Power Supplies Installing and Maintaining the E1200i System Removing and Replacing DC Power Supplies Remove an AC Power Supply in a non-redundant installationRemove an AC Power Supply in a redundant installation Installing and Maintaining the E1200i System Remove a DC Power Supply Removing and Replacing RPMs, Line Cards, or SFMs Removing and Replacing line cards or RPMsTo remove and replace E1200i line card or RPM modules Removing and Replacing SFMs To remove and replace an SFMNo linecard To remove and replace the air filter Removing and Replacing the Air Filter Removing and Replacing Components Appendix a Using a Flash Memory Card External Flash Memory Card OverviewInserting the External Flash Memory Card Removing the External Flash Memory Card To install the flash memory cardFormatting an External Flash Card To remove the flash memory card Command Syntax Command Mode Purpose Copying Files to the External FlashDisplaying Files Stored on the External Flash Page Booting from the Bootuser Prompt System Boot Process Step Command To configure the chassis from the Bootuser prompt Step Command Task Show boot selector Show bootvar View the Management interface’s physical settings Auto-negotiationPort Show default-gateway Default-gateway ip-address Step CommandTask Reload System Boot Appendix C Alarms Power Supplies and Alarms SFMs and Alarms Alarms E1200i AC System Power Requirements Appendix D System SpecificationsE1200i AC Chassis Physical Design This appendix contains two major sections System Specifications E1200i DC Chassis Physical Design E1200i DC System Power Requirements Operating Specifications Environmental SpecificationsAgency Compliance Non-operating Safety Standards and Compliance Agency Certifications Japan Vcci Compliance for Class a EquipmentKorea MIC certification Electromagnetic Emissions ImmunityProduct Recycling and Disposal European Weee symbol System Specifications This appendix contains these major sections Appendix E Technical Support Support Policies section of iSupport Accessing iSupport Services Output from the show logging eventlog unit command, where Output from the show tech-supportnon-paged command ThisConsole captures showing the error messages Console captures showing the troubleshooting steps taken To request replacement hardware, follow these steps Requesting a Hardware Replacement FPC Asic Index 104 Index Installing and Maintaining the E1200i System 105