Copyright 2008 Force10 Networks | Force10 Networks E1200i specification

Copyright 2008 Force10 Networks

All rights reserved. Printed in the USA. April 2008.

Force10 Networks® reserves the right to change, modify, revise this publication without notice.

Trademarks

Force10 Networks® and E-Series® are registered trademarks of Force10 Networks, Inc. Force10, the Force10 logo, E1200, E1200i, E600, E600i, E300, EtherScale, TeraScale, and FTOS are trademarks of Force10 Networks, Inc. All other brand and product names are registered trademarks or trademarks of their respective holders.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, Force10 Networks reserves the right to make changes to products described in this document without notice. Force10 Networks does not assume any liability that may occur due to the use or application of the product(s) described herein.

Note: The country-specific warnings and statements of compliance have been moved to “Agency Compliance” on page 94 in the appendix “System Specifications” on page 91.

Image 2

Force10 Networks E1200i manual Copyright 2008 Force10 Networks

Contents

Installing and Maintaining the E1200i System Copyright 2008 Force10 Networks Contents Installing Fan Trays Appendix B System Boot Index List of Figures Page List of Tables Page Defines the information symbols used throughout this guide Symbol Description Related Publications E1200i System Operating OverviewPage Page RPM Component Minimum Maximum Field-Replaceable Supplying Power DC on Step Task Section Chapter Site Preparation Site Selection Criteria Rack Mounting Cabinet PlacementPower Fans and Airflow Storing Components Installing the AC Chassis Unpacking the E1200i AC System Standard Front Chassis Mounting Installing the Equipment Rack Shelf BarTo install a equipment rack shelf bar Step Task Installing the Chassis into an Equipment Cabinet To install the chassis into a prepared rack Installing the AC Chassis Installing the DC Chassis Unpacking the E1200i DC System Installing the DC Chassis Rack-Mounting the Chassis Installing the DC Chassis Installing Fan Trays Screw latch Installing Fan Trays Label To install fan traysIs an illustration of the fan tray safety labels Location Installing Fan Trays Installing AC Power Supplies On/Standby Switch Installing Power Supplies Securing the Chassis Ground AC Power Supply and Fan Operability Test Insert power supply Step Task Status LED is Status Installing AC Power Supplies Installing DC Power Supplies PEM 0 and PEM 1 Chassis Locations Cable and Connector Requirements Installing DC PEMs Use the following steps to install a DC PEM Over current protector PEM interlock lever Locking screws Cable Connector Required for E1200i DC PEM DC PEM with Connections in Place DC Power Supply and Fan Operability Test Step Task Important Points to Remember Installing RPMs, Line Cards SFMsUnpacking an RPM or Line Card Line Cards Installing Line Cards and RPMsRPMs Preparing and Installing RPMs and Line Cards Blank Panels To install line cards and RPMs Installing an RPM into the E1200i Describes the RPM LED states and the RPM front panel Installing a Second RPMRPM Label and LEDs Section Label Description Installing Switch Fabric Modules SFMs SFM Front Panel and LEDs Illustrates the SFM front panel and LEDs Line Card Cable Management Systems RPM Ports Connecting the Console and Auxiliary PortsRPM Ports and Cables Pin Signal Input/Output Cable and Adapter Pin Assignments Accessing the Console with a DB-9 Adapter Accessing the Console with a DB-25 Adapter Label Description Accessing the 10/100 Ethernet Management PortAccessing the Auxiliary Port by Modem Chapter Powering Up Preparation Supplying Power AC Supplying Power DC Booting to the CLI Prompt Booting from the Bootuser Prompt Powering Up Removing and Replacing Components Removing and Replacing Fan Trays Removing and Replacing AC Power Supplies Removing and Replacing Components Installing and Maintaining the E1200i System Remove an AC Power Supply in a redundant installation Removing and Replacing DC Power SuppliesRemove an AC Power Supply in a non-redundant installation Installing and Maintaining the E1200i System Remove a DC Power Supply To remove and replace E1200i line card or RPM modules Removing and Replacing RPMs, Line Cards, or SFMsRemoving and Replacing line cards or RPMs No linecard Removing and Replacing SFMsTo remove and replace an SFM Removing and Replacing the Air Filter To remove and replace the air filter Removing and Replacing Components Inserting the External Flash Memory Card Appendix a Using a Flash Memory CardExternal Flash Memory Card Overview Formatting an External Flash Card To install the flash memory cardRemoving the External Flash Memory Card To remove the flash memory card Displaying Files Stored on the External Flash Command Syntax Command Mode PurposeCopying Files to the External Flash Page System Boot Process Booting from the Bootuser Prompt To configure the chassis from the Bootuser prompt Step Command Show boot selector Step Command Task Show bootvar Port View the Management interface’s physical settingsAuto-negotiation Step CommandTask Show default-gateway Default-gateway ip-address Reload System Boot Appendix C Alarms Power Supplies and Alarms SFMs and Alarms Alarms E1200i AC Chassis Physical Design Appendix D System SpecificationsE1200i AC System Power Requirements This appendix contains two major sections System Specifications E1200i DC System Power Requirements E1200i DC Chassis Physical Design Agency Compliance Environmental SpecificationsOperating Specifications Non-operating Korea MIC certification Safety Standards and Compliance Agency CertificationsJapan Vcci Compliance for Class a Equipment Product Recycling and Disposal Electromagnetic EmissionsImmunity European Weee symbol System Specifications Appendix E Technical Support This appendix contains these major sections Accessing iSupport Services Support Policies section of iSupport Console captures showing the error messages Output from the show tech-supportnon-paged command ThisOutput from the show logging eventlog unit command, where Console captures showing the troubleshooting steps taken Requesting a Hardware Replacement To request replacement hardware, follow these steps Index FPC Asic 104 Index Installing and Maintaining the E1200i System 105