Installing Fan Trays | Force10 Networks E1200i guide

34	Installing Fan Trays

Image 34

Force10 Networks E1200i manual Installing Fan Trays

Contents

Installing and Maintaining the E1200i System Copyright 2008 Force10 Networks Contents Installing Fan Trays Appendix B System Boot Index List of Figures Page List of Tables Page Defines the information symbols used throughout this guide Symbol Description Related Publications E1200i System Operating OverviewPage Page RPM Component Minimum Maximum Field-Replaceable Supplying Power DC on Step Task Section Chapter Site Preparation Site Selection Criteria Power Cabinet PlacementRack Mounting Fans and Airflow Storing Components Installing the AC Chassis Unpacking the E1200i AC System Standard Front Chassis Mounting Installing the Equipment Rack Shelf BarTo install a equipment rack shelf bar Step Task Installing the Chassis into an Equipment Cabinet To install the chassis into a prepared rack Installing the AC Chassis Installing the DC Chassis Unpacking the E1200i DC System Installing the DC Chassis Rack-Mounting the Chassis Installing the DC Chassis Installing Fan Trays Screw latch Installing Fan Trays Label To install fan traysIs an illustration of the fan tray safety labels Location Installing Fan Trays Installing AC Power Supplies On/Standby Switch Installing Power Supplies Securing the Chassis Ground AC Power Supply and Fan Operability Test Insert power supply Step Task Status LED is Status Installing AC Power Supplies Installing DC Power Supplies PEM 0 and PEM 1 Chassis Locations Cable and Connector Requirements Installing DC PEMs Use the following steps to install a DC PEM Over current protector PEM interlock lever Locking screws Cable Connector Required for E1200i DC PEM DC PEM with Connections in Place DC Power Supply and Fan Operability Test Step Task Unpacking an RPM or Line Card Installing RPMs, Line Cards SFMsImportant Points to Remember RPMs Installing Line Cards and RPMsLine Cards Preparing and Installing RPMs and Line Cards Blank Panels To install line cards and RPMs Installing an RPM into the E1200i Describes the RPM LED states and the RPM front panel Installing a Second RPMRPM Label and LEDs Section Label Description Installing Switch Fabric Modules SFMs SFM Front Panel and LEDs Illustrates the SFM front panel and LEDs Line Card Cable Management Systems RPM Ports and Cables Connecting the Console and Auxiliary PortsRPM Ports Pin Signal Input/Output Cable and Adapter Pin Assignments Accessing the Console with a DB-9 Adapter Accessing the Console with a DB-25 Adapter Accessing the Auxiliary Port by Modem Accessing the 10/100 Ethernet Management PortLabel Description Chapter Powering Up Preparation Supplying Power AC Supplying Power DC Booting to the CLI Prompt Booting from the Bootuser Prompt Powering Up Removing and Replacing Components Removing and Replacing Fan Trays Removing and Replacing AC Power Supplies Removing and Replacing Components Installing and Maintaining the E1200i System Remove an AC Power Supply in a non-redundant installation Removing and Replacing DC Power SuppliesRemove an AC Power Supply in a redundant installation Installing and Maintaining the E1200i System Remove a DC Power Supply Removing and Replacing line cards or RPMs Removing and Replacing RPMs, Line Cards, or SFMsTo remove and replace E1200i line card or RPM modules To remove and replace an SFM Removing and Replacing SFMsNo linecard Removing and Replacing the Air Filter To remove and replace the air filter Removing and Replacing Components External Flash Memory Card Overview Appendix a Using a Flash Memory CardInserting the External Flash Memory Card Formatting an External Flash Card To install the flash memory cardRemoving the External Flash Memory Card To remove the flash memory card Copying Files to the External Flash Command Syntax Command Mode PurposeDisplaying Files Stored on the External Flash Page System Boot Process Booting from the Bootuser Prompt To configure the chassis from the Bootuser prompt Step Command Show boot selector Step Command Task Show bootvar Auto-negotiation View the Management interface’s physical settingsPort Step CommandTask Show default-gateway Default-gateway ip-address Reload System Boot Appendix C Alarms Power Supplies and Alarms SFMs and Alarms Alarms E1200i AC Chassis Physical Design Appendix D System SpecificationsE1200i AC System Power Requirements This appendix contains two major sections System Specifications E1200i DC System Power Requirements E1200i DC Chassis Physical Design Agency Compliance Environmental SpecificationsOperating Specifications Non-operating Japan Vcci Compliance for Class a Equipment Safety Standards and Compliance Agency CertificationsKorea MIC certification Immunity Electromagnetic EmissionsProduct Recycling and Disposal European Weee symbol System Specifications Appendix E Technical Support This appendix contains these major sections Accessing iSupport Services Support Policies section of iSupport Console captures showing the error messages Output from the show tech-supportnon-paged command ThisOutput from the show logging eventlog unit command, where Console captures showing the troubleshooting steps taken Requesting a Hardware Replacement To request replacement hardware, follow these steps Index FPC Asic 104 Index Installing and Maintaining the E1200i System 105