Installing Fan Trays | Force10 Networks E1200i instruction

Chapter 6 Installing Fan Trays

Access the fan tray slots from the rear of the chassis (Figure 9). Two fan trays are required in the chassis. When a fan tray is not installed in the lower slot, a self-closing door will seal the slot. Panel blanks are not required. However, to ensure fail-safe chassis operation, do not operate the chassis with only one fan tray for more than 30 minutes.

Warning: Install the fan trays before you supply power to the system.

Warning: Electrostatic discharge (ESD) damage can occur when components are mishandled. Always wear an ESD-preventative wrist or foot-heal ground strap when handling chassis components. After you remove the original packaging, place chassis components on an antistatic surface.

Installing and Maintaining the E1200i System

31

Image 31

Force10 Networks E1200i manual Installing Fan Trays

Contents

Installing and Maintaining the E1200i System Copyright 2008 Force10 Networks Contents Installing Fan Trays Appendix B System Boot Index List of Figures Page List of Tables Page Symbol Description Defines the information symbols used throughout this guide Related Publications Operating Overview E1200i SystemPage Page RPM Component Minimum Maximum Field-Replaceable Step Task Section Supplying Power DC on Site Selection Criteria Chapter Site Preparation Power Cabinet PlacementRack Mounting Fans and Airflow Storing Components Unpacking the E1200i AC System Installing the AC Chassis Step Task Installing the Equipment Rack Shelf BarTo install a equipment rack shelf bar Standard Front Chassis Mounting To install the chassis into a prepared rack Installing the Chassis into an Equipment Cabinet Installing the AC Chassis Unpacking the E1200i DC System Installing the DC Chassis Installing the DC Chassis Rack-Mounting the Chassis Installing the DC Chassis Installing Fan Trays Screw latch Installing Fan Trays Location To install fan traysIs an illustration of the fan tray safety labels Label Installing Fan Trays On/Standby Switch Installing AC Power Supplies Securing the Chassis Ground Installing Power Supplies Insert power supply AC Power Supply and Fan Operability Test Status LED is Step Task Status Installing AC Power Supplies PEM 0 and PEM 1 Chassis Locations Installing DC Power Supplies Installing DC PEMs Cable and Connector Requirements Use the following steps to install a DC PEM Over current protector PEM interlock lever Locking screws Cable Connector Required for E1200i DC PEM DC PEM with Connections in Place DC Power Supply and Fan Operability Test Step Task Unpacking an RPM or Line Card Installing RPMs, Line Cards SFMsImportant Points to Remember RPMs Installing Line Cards and RPMsLine Cards Blank Panels Preparing and Installing RPMs and Line Cards Installing an RPM into the E1200i To install line cards and RPMs Section Label Description Installing a Second RPMRPM Label and LEDs Describes the RPM LED states and the RPM front panel Installing Switch Fabric Modules SFMs Illustrates the SFM front panel and LEDs SFM Front Panel and LEDs Line Card Cable Management Systems RPM Ports and Cables Connecting the Console and Auxiliary PortsRPM Ports Cable and Adapter Pin Assignments Pin Signal Input/Output Accessing the Console with a DB-25 Adapter Accessing the Console with a DB-9 Adapter Accessing the Auxiliary Port by Modem Accessing the 10/100 Ethernet Management PortLabel Description Preparation Chapter Powering Up Supplying Power DC Supplying Power AC Booting from the Bootuser Prompt Booting to the CLI Prompt Powering Up Removing and Replacing Fan Trays Removing and Replacing Components Removing and Replacing Components Removing and Replacing AC Power Supplies Installing and Maintaining the E1200i System Remove an AC Power Supply in a non-redundant installation Removing and Replacing DC Power SuppliesRemove an AC Power Supply in a redundant installation Installing and Maintaining the E1200i System Remove a DC Power Supply Removing and Replacing line cards or RPMs Removing and Replacing RPMs, Line Cards, or SFMsTo remove and replace E1200i line card or RPM modules To remove and replace an SFM Removing and Replacing SFMsNo linecard To remove and replace the air filter Removing and Replacing the Air Filter Removing and Replacing Components External Flash Memory Card Overview Appendix a Using a Flash Memory CardInserting the External Flash Memory Card To remove the flash memory card To install the flash memory cardRemoving the External Flash Memory Card Formatting an External Flash Card Copying Files to the External Flash Command Syntax Command Mode PurposeDisplaying Files Stored on the External Flash Page Booting from the Bootuser Prompt System Boot Process Step Command To configure the chassis from the Bootuser prompt Step Command Task Show boot selector Show bootvar Auto-negotiation View the Management interface’s physical settingsPort Show default-gateway Default-gateway ip-address Step CommandTask Reload System Boot Appendix C Alarms Power Supplies and Alarms SFMs and Alarms Alarms This appendix contains two major sections Appendix D System SpecificationsE1200i AC System Power Requirements E1200i AC Chassis Physical Design System Specifications E1200i DC Chassis Physical Design E1200i DC System Power Requirements Non-operating Environmental SpecificationsOperating Specifications Agency Compliance Japan Vcci Compliance for Class a Equipment Safety Standards and Compliance Agency CertificationsKorea MIC certification Immunity Electromagnetic EmissionsProduct Recycling and Disposal European Weee symbol System Specifications This appendix contains these major sections Appendix E Technical Support Support Policies section of iSupport Accessing iSupport Services Console captures showing the troubleshooting steps taken Output from the show tech-supportnon-paged command ThisOutput from the show logging eventlog unit command, where Console captures showing the error messages To request replacement hardware, follow these steps Requesting a Hardware Replacement FPC Asic Index 104 Index Installing and Maintaining the E1200i System 105