SERVICE AND MAINTENANCE

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary.

To remove skid shoes:

1.Remove the four carriage bolts and hex flange nuts which secure them to the snow thrower.

2.Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. Refer to Figure 17.

To remove shave plate:

1.Remove the carriage bolts and hex nuts which attach it to the snow thrower housing.

2.Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely.

Adjustments

Shift Cable

If the full range of speeds (forward and reverse) cannot be achieved, refer to the figure to the right and adjust the shift cable as follows:

1.Place the shift lever in the fastest forward speed position.

2.Loosen the hex nut on the shift cable index bracket. See Figure 18.

3.Pivot the bracket downward to take up slack in the cable.

4.Retighten the hex nut.

Drive Control

When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. Also,

if there is excessive slack in the drive cable or if the unit experiences intermittent drive while using, the cable may need to be adjusted. Check the adjustment of the drive control as follows:

1.With the drive control released, push the snow thrower gently forward. The unit should roll freely.

2.Engage the drive control and gently attempt to push the snow thrower forward. The wheels should not turn. The unit should not roll freely.

3.With the drive control released, move the shift lever back and forth between the R2 position and the F5 position several times. There should be no resistance in the shift lever.

4.If any of the above tests failed, the drive cable is in need of adjust- ment. Proceed as follows:

5.Loosen the lower hex nut on the drive cable bracket. See Figure 19.

6.Position the bracket upward to provide more slack (or downward to increase cable tension).

7.Retighten the lower hex nut.

NOTE: Augers not shown for clarity.

Figure 17

Figure 18

Figure 19

18

Page 18
Image 18
Craftsman 247.8819 operating instructions Shave Plate and Skid Shoes, Shift Cable, Drive Control

247.8819 specifications

The Craftsman 247.8819 is a highly versatile and robust lawn mower designed for homeowners seeking a reliable and efficient tool to maintain their lawns. This mower stands out due to its impressive features, advanced technologies, and thoughtful characteristics that cater to both novice and experienced users.

One of the main features of the Craftsman 247.8819 is its powerful engine. Equipped with a reliable gas engine, it offers strong performance and the capability to tackle tough grass, ensuring a clean and precise cut every time. The high torque output allows this mower to handle various terrains with ease, making it a perfect choice for yards of different sizes and complexities.

Another remarkable feature is its variable speed transmission. This technology allows users to adjust the speed of the mower according to their comfort and specific mowing requirements. With the ability to operate at different speeds, users can maneuver through tight corners or open spaces more effectively, making for a more efficient mowing experience.

The cutting deck of the Craftsman 247.8819 is designed to provide optimal cutting performance. With a generous width, it enables users to cover more ground in less time. Additionally, it features multiple height adjustment settings, allowing for customized cutting heights to promote healthy grass growth. Whether users prefer a low cut for a manicured lawn or a higher cut for a more natural look, this mower can adapt accordingly.

Comfort and ease of use are also prioritized in the Craftsman 247.8819. Its ergonomic handles are designed to minimize strain during operation, and the mower's lightweight construction ensures easy maneuverability. Moreover, the mower is equipped with large, durable wheels that provide stability across varied terrains while ensuring smooth operation.

Maintenance is made simple with the Craftsman 247.8819. Its design promotes easy access to the engine and other components, allowing for straightforward maintenance tasks such as oil changes and blade sharpening. This ensures the mower remains in top condition and continues to perform efficiently over time.

In summary, the Craftsman 247.8819 offers a powerful engine, variable speed transmission, versatile cutting heights, and an ergonomic design, making it an excellent choice for homeowners. Its thoughtful features and ease of maintenance solidify its reputation as a dependable lawn mower for keeping lawns looking their best.