• | Hold the square end of the threaded | • | Disconnect | the spark plug wire. | ||||||
| portion with pliers and adjust the Iocknut | • | Remove the belt cover (see figure below). | |||||||
| in or out until the excess slack is removed |
|
|
|
| |||||
| (see last figure on page 14). |
|
|
|
|
| Cover | |||
• | Pull the cable back through the spring and |
|
|
| ||||||
| connect the cable (see last figure on page |
|
|
|
| |||||
| 14). |
|
|
|
|
|
|
|
| |
NOTE: Whenever the auger belt is replaced, |
|
|
|
| ||||||
the cables will need to be adjusted. |
|
| _ | _ | Belt | |||||
TO ADJUST AUGER DRIVE BELT |
|
| ||||||||
|
|
| ||||||||
Belt stretches during normal use. If your |
|
| ||||||||
|
|
|
| |||||||
snow thrower will not discharge snow, or a |
| 1/4 X 1/2" Self Tapping Screw | ||||||||
squealing noise is heard when the |
| • Loosen the belt guide (see next figure) | ||||||||
snowthrewer is put into deep snow, your au- | ||||||||||
| and pull away from the auger drive pulley. | |||||||||
ger idler pulley may need to be adjusted. |
| |||||||||
• | Slip beR from auger drive pulley. | |||||||||
• | Check the control cables for proper ad- | |||||||||
• Pull auger idler pulley to the engaged po- | ||||||||||
| justment. (See section for Clutch Control | |||||||||
|
| sition, releasing brake. |
| |||||||
| Cable Adjustment on page 14). |
|
|
| ||||||
|
| • Slip belt from between brake arm and | ||||||||
• | If the cables are | adjusted correctly | then | |||||||
| pulley. |
|
| |||||||
| proceed with adjusting the idler pulley. |
|
|
| ||||||
| • | Remove | old belt. |
| ||||||
• Disconnect the spark plug wire. |
|
| ||||||||
| • Install new replacement belt of the same | |||||||||
• Remove the belt cover. (See second fig- | ||||||||||
| type onto the auger pulley. | |||||||||
| ure on this page) |
|
|
|
| |||||
|
|
|
| • Position belt onto auger drive pulley. | ||||||
• | With a 9/16'wrench, loosen | the nut on the | ||||||||
• Adjust belt guide (see to Adjust Belt | ||||||||||
| idler pulley. Move the idler pulley in toward | |||||||||
|
| Guide paragraph). |
| |||||||
| the engine pulley approximately 1/8". |
|
| |||||||
| • Reinstall the belt cover. | |||||||||
• | Tighten nut. |
|
|
|
| |||||
|
|
|
| • Check the clutch control cable adjustment | ||||||
• | Press the auger drive lever. Check the | |||||||||
| (see paragraph on page 14). | |||||||||
| tension on the belt(opposite auger idler | • | Reconnect spark plug wire. | |||||||
| pulley). The belt should deflect about 1/2" | |||||||||
|
| Auger | Belt Guide | TractionDrive | ||||||
| with moderate | pressure(see | figure | below). |
| |||||
• Reinstall the | belt | cover. |
| 'oy | idler | |||||
|
| |||||||||
| Au o |
|
| |||||||
|
|
|
|
|
|
| Belt |
|
| |
|
|
|
|
|
|
| Loosen |
|
| |
|
|
|
|
|
|
| nut |
|
| |
| Pulley | / | '_ Deflection |
| Auger |
|
| |||
|
|
|
|
|
|
| Idler |
|
| |
|
|
|
|
|
|
| Pulley I |
|
| |
Pulley
Engaged _
TO REPLACE BELT
The drive belt on this snow thrower is of
special construction and should be replaced with original equipment, belts are available
from your nearest Craftsman Store or Serv- ice Center.
A_ CAUTION: Oreintheqasoline out-
doors, away from the _"ireor Tlame
If your snow thrower will not discharge snow, and the auger drive belt (see second
figure on page for location) is damaged, re- place it as follows:
TO ADJUSTTHE BELT GUIDE
•Disconnect the spark plug wire.
•Remove the belt cover by removing the screw and flatwasher on the left and right hand side (see second figure on this page).
•Engage the auger drive clutch lever.
•Measure the distance between the belt guide and the belt (see figure below). The distance should be 1/8" for belt guide.
•If adjustment is necessary, loosen the belt guide mounting bolt. Move the belt guide to the correct position. Tighten the
15
