![](/images/new-backgrounds/1098193/9819343x1.webp)
| CAUTION:Blades are sharp. Protect | Blade | ||||||
your hands with gloves and/or wrap | ||||||||
| ||||||||
blade with heavy | cloth. |
|
|
| ||||
Check adjustment on right side of tractor. |
| |||||||
Position any blade so the tip is pointing |
| |||||||
straight forward. Measure distance "B" at |
| |||||||
front and | rear tip | of blade |
|
|
| |||
• | Before | making | any | necessary | adjust- | BOTH FRONT LINKS MUST BE EQUAL | ||
| ments, check that both front links are | |||||||
| IN LENGTH | |||||||
| equal | in length. |
|
|
| |||
|
|
|
|
| ||||
• | If links | are not | equal | in | length, | adjust |
| |
| one link to same length as other link. |
| ||||||
• To lower front of blade, loosen nut "C" |
| |||||||
| on both front links an equal number of _ |
| ||||||
| turns. |
|
|
|
|
|
| |
NOTE: Each full turn of nut "C" will |
| |||||||
change dim. "B" by approximately | 3/16". |
| ||||||
• When distance "B" is 1/8" to 1/2" lower |
| |||||||
| at front than rear, tighten nut "D" |
| ||||||
| against trunnion on both front links. |
| ||||||
• | To raise front | of blade, | loosen | nut "D" | Nut | |||
| from trunnion on both front links. | |||||||
|
| |||||||
| Tighten nut "C" on both front links an |
| ||||||
| equal | number | of turns. |
|
|
|
•When distance "B" is 1/8" to 1/2" lower at front than rear, tighten nut "D"
| against | trunnion | on | both front | links. | Front Plate |
|
| Trunnion |
|
| ||||||||||
• Recheck |
| adjustment. | Assembly |
|
|
|
|
|
|
|
| ||||||||||
TO REPLACE | MOWER |
| DRIVE | BELT | 8. Remove | belt | from electric | clutch | |||||||||||||
MOWER | DRIVE BELT |
| REMOVAL | pulley. |
|
|
|
|
|
|
|
| |||||||||
| 9. Remove belt from idler pulleys. | ||||||||||||||||||||
1. Park tractor on a level surface. | |||||||||||||||||||||
10.Check primary idler arm and two | |||||||||||||||||||||
| Engage | parking | brake. |
|
| ||||||||||||||||
|
|
| idlers to see that they rotate freely. | ||||||||||||||||||
2. Lower mower to its lowest position. | |||||||||||||||||||||
11.Be sure spring is securely hooked to | |||||||||||||||||||||
3. Disengage belt tension rod from lock | |||||||||||||||||||||
primary idler arm and spring arm. | |||||||||||||||||||||
| bracket. |
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
| MOWER | DRIVE | BELT | INSTALLATION | |||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||||
_ | CAUTION: | Rod | is spring | loaded. | 12.Install | belt | in | both | idlers. |
|
| ||||||||||
Have a | firm | grip | on | rod | and release | 13.Install | new | belt onto | electric | clutch | |||||||||||
slowly. |
|
|
|
|
|
|
|
|
| pulley. |
|
|
|
|
|
|
|
| |||
4. Remove screws from R.H. | mandrel | 14.Carefully | roll | belt | into | upper | groove of | ||||||||||||||
| cover | and | remove | cover. |
|
| R.H. | mandrel | pulley. |
|
|
| |||||||||
5. | Remove | any | dirt | or | grass | clippings | 15.Carefully | check | belt | routing | making | ||||||||||
| which | may | have | accumulated | around | sure | belt | is in the grooves | correctly. | ||||||||||||
| mandrels | and | entire | upper |
| deck | 16.Reconnect |
| R.H. | suspension |
| arm to | |||||||||
| surface. |
|
|
|
|
|
|
|
| rear | deck |
| bracket |
| with retainer spring. |
6.Disconnect R.H. suspension arm from 17.Reassemble R.H. mandrel cover.
rear deck bracket by removing | 18.Engage | belt tension rod by pushing |
retainer spring. | rod into | locking bracket. |
7.Carefully roll belt over the top of R.H. mandrel pulley.
22