IDE Connector CN2, Connecting the hard drive | Creative PCA-6780

2.14 IDE Connector (CN2)

The PCA-6780 provides one IDE channels to which you can attach up to two Enhanced Integrated Device Electronics hard disk drives or CDROM to the PCA-6780’s internal controller. The PCA-6780's IDE controller uses a PCI interface. This advanced IDE controller supports faster data transfer, PIO Mode 3 or Mode 4, UDMA 33/66/100 mode.

2.14.1 Connecting the hard drive

Connecting drives is done in a daisy-chain fashion. It requires one of two cables (not included in this package), depending on the drive size. 1.8" and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector. 3.5" drives use a 1 x 44-pin to 2 x 40-pin connector.

Wire number 1 on the cable is red or blue, and the other wires are gray.

1.Connect one end of the cable to CN2. Make sure that the red (or blue) wire corresponds to pin 1 on the connector, which is labeled on the board (on the right side).

2.Plug the other end of the cable into the Enhanced IDE hard drive,

with pin 1 on the cable corresponding to pin 1 on the hard drive. (See your hard drive’s documentation for the location of the con- nector.)

If desired, connect a second drive as described above.

Unlike floppy drives, IDE hard drives can connect to either end of the cable. If you install two drives, you will need to set one as the master and one as the slave by using jumpers on the drives. If you install only one drive, set it as the master.

17	Chapter 2 Installation

Image 27

Creative PCA-6780 user manual IDE Connector CN2, Connecting the hard drive

Contents

PCA-6780 Acknowledgements Copyright Packing List Additional Information and Assistance Page Page Contents Appendix a Programming Gpio & Watchdog Timer Table B.5IR Connector Appendix C General Information Introduction System chipsets Intel 852GM +ICH4 FeaturesSpecifications Standard SBC Functions Mechanical and Environmental Display InterfaceSolid State disk Ethernet interface Board layout dimensions component side Board layout dimensionsPage Installation Jumpers Jumpers Connectors Connectors Locating Connectors solder side Locating Connectors component side Setting Jumpers Clear Cmos J1 Clear Cmos J1 COM2 RS-232/422/485 Select Lvds Panel Power Select JP1Lvds Panel Power Select COM2 RS-232/422/485 Select J2 ATX power Connector CN5 Installing SODIMMs Printer port Connector CN4 CompactFlash SocketCompactFlash CN22 Connecting the floppy drive Floppy Connector CN3 Connecting the hard drive IDE Connector CN2 15 VGA/LVDS interface connections CRT display Connector CN10Lvds LCD panel Connector CN8 LCD Inverter Connector CN6 Network boot USB Connectors CN9,CN11Ethernet configuration LAN Connector CN13 HDD LED Pin1&Pin2,Pin3&Pin4,Pin5&Pin6 HDD LED/Reset/Power Button CN1Reset Pin7&Pin8 Power Button Pin9&Pin10 Audio Interface Connector CN7 COM port Connector CN14,CN15Mini Keyboard Connector CN17 External Keyboard Connector CN18Page Bios Operation Bios Introduction Control Keys Bios Setup Main Menu Exit Without Saving Load Optimized DefaultsSet Password Save & Exit Setup Standard Cmos Features Total Memory Halt onBase Memory Extended Memory Advanced Bios Features Boot Up NumLock StatusDisabled First / Second / Third / Other Boot DriveSwap Floppy DriveDisabled Boot Up Floppy SeekDisabled MPS Version Control for OS1.4 Security OptionSetupVideo Bios ShadowEnabled Full Screen Logo ShowEnabled Advanced Chipset Features Delayed Transaction Enabled System Bios CacheableEnabledVideo Bios CacheableDisabled Memory Hole At 15M-16MDisabled On-Chip VGA Enabled Boot Display Vbios DefaultOn-Chip Frame Buffer Size 32MB Super IO Device Integrated PeripheralsOnChip IDE Device Onboard Device Power ManagementMin Saving Power Management SetupAcpi FunctionEnabled Run VGA Bios if S3 ResumeAuto Wake-Up by PCI cardEnabled Suspend Mode 1 HourHDD Power Down Mode15 Min Soft-Off by PWR-BTTNEnabled Resume by AlarmDisabled USB KB Wake-Up From S3Enabled 7 PnP/PCI Configurations Shutdown Temperature Disabled PC Health StatusCurrent System/CPU Temp Show Only Frequency/Voltage Control Auto Detect PCI Clk EnabledSpread Spectrum Disabled CPU Host/SRC/PCI Clock Default Load Optimized Defaults Set Password To Establish PasswordTo Change Password To Disable Password Quit Without Saving Save & Exit SetupPage Page Driver Installation Step Driver Introduction Install Audio Driver for Windows XP/2000 Driver InstallationInstall Intel INF Update Driver for Windows XP/2000 Install Intel Graphic Driver for Windows XP 2000Page Programming Gpio & Watchdog Timer Appendix a Programming Gpio & Watchdog Timer Supported Gpio RegisterGpio Registers Gpio Example program-1 MOV DX,2EH MOV AL,AAH OUT DX,AL Watchdog programming Page Pin Assignments HDD LED/Reset/Power Button CN1 Table B.1 HDD LED/Reset/Power Button CN1Appendix B Pin Assignments Table B.2 Primary IDE Connector CN2 Primary IDE Connector CN2 Table B.3 Floppy Connector Floppy Connector Table B.5 IR Connector Printer Port ConnectorIR Connector Table B.4 Printer Port Connector Table B.7 Audio Interface CN7 Lvds Connector CN8Table B.8 Lvds Connector CN8 Audio Interface CN7 12 PC 104 Connector USB port 1, 2 Connector CN9SUB VGA Connector CN10 USB port 3,4 Connector CN11 LAN RJ45 Connector CN13 COM port 1 RS-232CN14COM port 2 RS-232/422/485CN15 ISA Gold Finger CN19 ATX Suspend Power Connector CN20 ATX Power Connector CN1617 KB/MS Connector CN17 External KB/mouse Connector CN18 Negative Power Input CN21 CF Connector CN22Table B.19 Negative Power Input CN21 Table B.21 Clear Cmos J1 Lvds Voltage Choose JP13 232/422/485 SEL J2 Table B.20 Lvds Voltage Choose JP1Page System Assignments Appendix C System Assignments System I/O PortsTable C.1 System I/O ports Table C.2 1st MB memory map 1st MB memory map Table C.3 DMA channel assignments DMA channel assignments Table C.4 Interrupt assignments Interrupt assignments