XLC Series Power Amplifiers | XLC系列功率放大器 |
5.Setup (continued)
5.安装（接上一页）
Figure 2.12 Bridge Mode
图2.12 桥接模式
- |
+ |
Bridge 桥接:
ON
1 2
JBL 4641
T
S
U
A
H
X
E
R
I
A
T
O
H
ON
1 2
Ch. 1 Source
2.7.3 | Bridge Mode | 2.7.3 桥接模式 | |
Typical input and output bridge wiring is shown in figure 2.12. The input of Channel 1 will be used. | 图2.12为一个常用的桥接输入和输出接线示例。使用的为通道1的输入。 | ||
1. | Set the Mode Switch to Bridge | 1. |
|
2. | Connect Channel 1 loudspeaker’s positive (+) lead to Bridge positive (red) terminal of amp; repeat for Channel 1’s | 2. | 将通道1扬声器的正极（+）导线连接到功放桥接的正极（红色）端子上，用同样的方法， |
| negative |
| 连接好通道1的负极。 |
2.8 Connecting to AC Mains | 2.8 连接到电源 |
Connect your amplifier to the AC mains power source (power outlet) with the supplied AC power cord. First, connect the | 使用功放原装的电源线，将您的功放连接到电源上（电源插座）。首先，将电线的IEC端连接到 |
IEC end of the cord to the IEC connector on the amplifier; then, plug the other end of the cord to the AC mains. | 功放的IEC接口上，然后将电线的另一端插入电源插座。 |
WARNING: The third prong of this connector (ground) is an important safety feature. Do not attempt to disable | 警告：此接口的第三个插脚（接地端）在安全性上起着至关重要的作用。切忌试图使用 |
this ground connection by using other methods. | 其他方法禁用此接地连接。 |
Amplifiers don’t create energy. The AC mains voltage and current must be sufficient to deliver the power you expect. You | 功放不产生能量。请确保交流电的电压和电流充足，从而供给功放所需的电能。功放所需要的交 |
must operate your amplifier from an AC mains power source with not more than a 10% variation above or below the | 流电源的电压不能高于或低于功放指定工作电压的10%，并符合指定的功率要求（指定的电源电 |
amplifier’s specified line voltage and within the specified frequency requirements (The specific voltage and frequency | 源和功率要求与经销商所在地匹配，具体数值在功放后面板的标签有标示）。如果您不能确定交 |
requirement is compatible to retailer’s location and dictated on the amplifier’s back panel label). If you are unsure of the | 流电源的输出电压值，请咨询您当地的电工。 |
output voltage of your AC mains, please consult your electrician. |
|
2.9 保护您的扬声器
2.9 Protecting Your Speakers
| 在常规使用中，需避免功放接收到削波。因为削波不仅会导致声音质量变差，而且还会损坏扬声 |
It’s wise to avoid clipping the amplifier signal. Not only does clipping sound bad, it can damage | 器高频驱动单元。 |
speakers. |
|
|
|
|
|
|
Operation Manual | 操作手册 | page 11 | ||
