Manuals / Crown Boiler / Household Appliance / Boiler

Crown Boiler M600 installation instructions Manufacturer of Hydronic Heating Products, BWC Series

Models: M600

1 22

Download 22 pages 62.75 Kb

Page 1

Image 1

D E S I G N E D T O L E A D

BWC Series

BWC150/225 CONCENTRIC VENTING INSTALLATION INSTRUCTIONS

These instructions must be afﬁxed on or adjacent to the boiler.

Models:

•BWC150

•BWC225

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury, or loss of life. For assistance or additional information, con- sult a qualiﬁed installer, service agency or the gas supplier. This boiler requires a special venting system. Read these instructions carefully before installing.

Manufacturer of Hydronic Heating Products

P.O. Box 14818 3633 I. Street

Philadelphia, PA 19134

Tel: (215) 535-8900 • Fax: (215) 535-9736 • www.crownboiler.com

Page 1

Image 1

Crown Boiler M600 installation instructions Manufacturer of Hydronic Heating Products, BWC Series, Models, BWC150 BWC225

Contents

P.O. Box 14818 3633 I. Street Philadelphia, PA Manufacturer of Hydronic Heating ProductsBWC150/225 CONCENTRIC VENTING INSTALLATION INSTRUCTIONS BWC SeriesPage B. Concentric Vent Adapter Kit Installation Table of ContentsC. Assembly of Crown Concentric Venting and Condensate Drain A. Concentric Vent System DesignConcentric Venting For BWC150 and BWC225 Do not install a barometric damper or drafthood on this boilerA. Concentric Vent System Design Do not attempt to mix components from different approved vent systemsExample Do not install the vent terminal directly over windows or doors45 Elbow Uncut Terminal Section 4 Permitted Terminals for Horizontal VentingMINIMUM TABLE 1.1 SUMMARY OF HORIZONTAL VENTING OPTIONS6 Permitted Terminals for Vertical Venting FIGURE 1.2 HORIZONTAL CONCENTRIC VENTING VENT OPTION 3,4FIGURE 1.3c POSITIONING VENT TERMINAL UNDER OVERHANGS TABLE 1.5 SUMMARY OF VERTICAL VENTING OPTIONS TABLE 1.4 VENT/ AIR INTAKE FITTING EQUIVALENT LENGTHVENT TABLE 1.6b CROWN CONCENTRIC100/150 VENT COMPONENTS VENT OPTIONS 8,9 TABLE 1.6a CROWN CONCENTRIC 80/125 VENT COMPONENTS VENT OPTIONS 3,8FIGURE 1.7 VERTICAL CONCENTRIC VENT SYSTEM VENT OPTION B. Concentric Vent Adapter Kit Installation1 The Concentric Vent Adapter Kits include Descriptionh Replace and tighten the clamp on the vent collar FIGURE 1.8 CONCENTRIC VENT ADAPTER ASSEMBLYj Use the exposed holes to line up the air intake box and gasket 80/125 C. Assembly of Crown Concentric Venting100/150 230517b Remove the plastic inner pipe by pulling it out from the female end f Reinstall the inner pipe 3 Joining Piped Make an insertion mark 1” from the male end of the outer pipe FIGURE 1.10 CUTTING STRAIGHT PIPEFIGURE 1.11b JOINING NON CUTTABLE PIPE 4 Horizontal Terminal Installation FIGURE 1.11a JOINING CUTTABLE PIPEFIGURE 1.12b CUTTING OUTER PIPE OF HORIZONTAL TERMINAL FIGURE 1.12a DIMENSION “L”, HORIZONTAL TERMINALFIGURE 1.12c CUTTING INNER PIPE OF HORIZONTAL TERMINAL FIGURE 1.12d COMPLETING HORIZONTAL TERMINAL INSTALLATIONFIGURE 1.13a DIMENSION “H” FIGURE 1.13b CUTTING VERTICAL TERMINAL FIGURE 1.13c COMPLETING VERTICAL TERMINAL INSTALLATIONVERTICAL TERMINAL FLAT ROOF FLASHING WEATHER TIGHT FLAT ROOF FIGURE 1.14 CHIMNEY CHASE INSTALLATIONOVER ORIGINAL OPENING UNUSED CHIMNEY SUPPORT ELBOW FROM BO ILER CHIMNEY CHASE BRACKET INCLUDED WITH SUPPORT ELBOW MID X MACHINE SCREWFIGURE 1.15 CONDENSATE DRAIN LINE ASSEMBLY P.O. Box 14818 3633 I. Street Philadelphia, PA Manufacturer of Hydronic Heating ProductsPN 980241 Rev BWC - 12/07