Manuals / Crown Boiler / Household Appliance / Boiler

Crown Boiler M600 Manufacturer of Hydronic Heating Products, PN 980241 Rev BWC - 12/07

Models: M600

1 22

Download 22 pages 62.75 Kb

Page 22

PN: 980241 Rev. 0

Manufacturer of Hydronic Heating Products

P.O. Box 14818 3633 I. Street

Philadelphia, PA 19134

Tel: (215) 535-8900 • Fax: (215) 535-9736 • www.crownboiler.com

PN: 980241 Rev. 0

BWC - 12/07

Image 22

Crown Boiler M600 Manufacturer of Hydronic Heating Products, P.O. Box 14818 3633 I. Street Philadelphia, PA

Contents

BWC150/225 CONCENTRIC VENTING INSTALLATION INSTRUCTIONS Manufacturer of Hydronic Heating ProductsP.O. Box 14818 3633 I. Street Philadelphia, PA BWC SeriesPage C. Assembly of Crown Concentric Venting and Condensate Drain Table of ContentsB. Concentric Vent Adapter Kit Installation A. Concentric Vent System DesignA. Concentric Vent System Design Do not install a barometric damper or drafthood on this boilerConcentric Venting For BWC150 and BWC225 Do not attempt to mix components from different approved vent systems45 Elbow Uncut Terminal Section Do not install the vent terminal directly over windows or doorsExample 4 Permitted Terminals for Horizontal VentingTABLE 1.1 SUMMARY OF HORIZONTAL VENTING OPTIONS MINIMUMFIGURE 1.2 HORIZONTAL CONCENTRIC VENTING VENT OPTION 3,4 6 Permitted Terminals for Vertical VentingFIGURE 1.3c POSITIONING VENT TERMINAL UNDER OVERHANGS TABLE 1.5 SUMMARY OF VERTICAL VENTING OPTIONS TABLE 1.4 VENT/ AIR INTAKE FITTING EQUIVALENT LENGTHVENT TABLE 1.6a CROWN CONCENTRIC 80/125 VENT COMPONENTS VENT OPTIONS 3,8 TABLE 1.6b CROWN CONCENTRIC100/150 VENT COMPONENTS VENT OPTIONS 8,91 The Concentric Vent Adapter Kits include B. Concentric Vent Adapter Kit InstallationFIGURE 1.7 VERTICAL CONCENTRIC VENT SYSTEM VENT OPTION Descriptionh Replace and tighten the clamp on the vent collar FIGURE 1.8 CONCENTRIC VENT ADAPTER ASSEMBLYj Use the exposed holes to line up the air intake box and gasket 100/150 C. Assembly of Crown Concentric Venting80/125 230517d Make an insertion mark 1” from the male end of the outer pipe f Reinstall the inner pipe 3 Joining Pipeb Remove the plastic inner pipe by pulling it out from the female end FIGURE 1.10 CUTTING STRAIGHT PIPE4 Horizontal Terminal Installation FIGURE 1.11a JOINING CUTTABLE PIPE FIGURE 1.11b JOINING NON CUTTABLE PIPEFIGURE 1.12a DIMENSION “L”, HORIZONTAL TERMINAL FIGURE 1.12b CUTTING OUTER PIPE OF HORIZONTAL TERMINALFIGURE 1.12d COMPLETING HORIZONTAL TERMINAL INSTALLATION FIGURE 1.12c CUTTING INNER PIPE OF HORIZONTAL TERMINALFIGURE 1.13a DIMENSION “H” FIGURE 1.13c COMPLETING VERTICAL TERMINAL INSTALLATION FIGURE 1.13b CUTTING VERTICAL TERMINALOVER ORIGINAL OPENING UNUSED CHIMNEY SUPPORT ELBOW FROM BO ILER FIGURE 1.14 CHIMNEY CHASE INSTALLATIONVERTICAL TERMINAL FLAT ROOF FLASHING WEATHER TIGHT FLAT ROOF CHIMNEY CHASE BRACKET INCLUDED WITH SUPPORT ELBOW MID X MACHINE SCREWFIGURE 1.15 CONDENSATE DRAIN LINE ASSEMBLY P.O. Box 14818 3633 I. Street Philadelphia, PA Manufacturer of Hydronic Heating ProductsPN 980241 Rev BWC - 12/07