Manuals / Crown Boiler / Household Appliance / Boiler

Crown Boiler M600 installation instructions 14 CHIMNEY CHASE INSTALLATION

Models: M600

1 22

Page 20

WARNING

•Do not attempt to construct a vertical vent system inside a chimney that is used to vent a ﬁreplace or other appliances.

•Do not attempt to construct a vertical vent system inside a chimney ﬂue adjacent to another ﬂue used by a ﬁreplace or other appliances.

VERTICAL TERMINAL

FLAT ROOF FLASHING

WEATHER TIGHT FLAT ROOF

OVER ORIGINAL OPENING

UNUSED CHIMNEY

SUPPORT ELBOW

FROM BO ILER ----

CHIMNEY CHASE BRACKET

(INCLUDED WITH SUPPORT ELBOW)

MID X 35

MACHINE SCREW

FIGURE 1.14: CHIMNEY CHASE INSTALLATION

DRILL HOLE IN REAR OF OLD CHIMNEY TO RECEIVE BRACKET PIN

Page 20

Image 20

Crown Boiler M600 14 CHIMNEY CHASE INSTALLATION, Vertical Terminal Flat Roof Flashing Weather Tight Flat Roof

Contents

Manufacturer of Hydronic Heating Products P.O. Box 14818 3633 I. Street Philadelphia, PABWC150/225 CONCENTRIC VENTING INSTALLATION INSTRUCTIONS BWC SeriesPage Table of Contents B. Concentric Vent Adapter Kit InstallationC. Assembly of Crown Concentric Venting and Condensate Drain A. Concentric Vent System DesignDo not install a barometric damper or drafthood on this boiler Concentric Venting For BWC150 and BWC225A. Concentric Vent System Design Do not attempt to mix components from different approved vent systemsDo not install the vent terminal directly over windows or doors Example45 Elbow Uncut Terminal Section 4 Permitted Terminals for Horizontal VentingTABLE 1.1 SUMMARY OF HORIZONTAL VENTING OPTIONS MINIMUMFIGURE 1.2 HORIZONTAL CONCENTRIC VENTING VENT OPTION 3,4 6 Permitted Terminals for Vertical VentingFIGURE 1.3c POSITIONING VENT TERMINAL UNDER OVERHANGS VENT TABLE 1.4 VENT/ AIR INTAKE FITTING EQUIVALENT LENGTHTABLE 1.5 SUMMARY OF VERTICAL VENTING OPTIONS TABLE 1.6a CROWN CONCENTRIC 80/125 VENT COMPONENTS VENT OPTIONS 3,8 TABLE 1.6b CROWN CONCENTRIC100/150 VENT COMPONENTS VENT OPTIONS 8,9B. Concentric Vent Adapter Kit Installation FIGURE 1.7 VERTICAL CONCENTRIC VENT SYSTEM VENT OPTION1 The Concentric Vent Adapter Kits include Descriptionj Use the exposed holes to line up the air intake box and gasket FIGURE 1.8 CONCENTRIC VENT ADAPTER ASSEMBLYh Replace and tighten the clamp on the vent collar C. Assembly of Crown Concentric Venting 80/125100/150 230517f Reinstall the inner pipe 3 Joining Pipe b Remove the plastic inner pipe by pulling it out from the female endd Make an insertion mark 1” from the male end of the outer pipe FIGURE 1.10 CUTTING STRAIGHT PIPE4 Horizontal Terminal Installation FIGURE 1.11a JOINING CUTTABLE PIPE FIGURE 1.11b JOINING NON CUTTABLE PIPEFIGURE 1.12a DIMENSION “L”, HORIZONTAL TERMINAL FIGURE 1.12b CUTTING OUTER PIPE OF HORIZONTAL TERMINALFIGURE 1.12d COMPLETING HORIZONTAL TERMINAL INSTALLATION FIGURE 1.12c CUTTING INNER PIPE OF HORIZONTAL TERMINALFIGURE 1.13a DIMENSION “H” FIGURE 1.13c COMPLETING VERTICAL TERMINAL INSTALLATION FIGURE 1.13b CUTTING VERTICAL TERMINALFIGURE 1.14 CHIMNEY CHASE INSTALLATION VERTICAL TERMINAL FLAT ROOF FLASHING WEATHER TIGHT FLAT ROOFOVER ORIGINAL OPENING UNUSED CHIMNEY SUPPORT ELBOW FROM BO ILER CHIMNEY CHASE BRACKET INCLUDED WITH SUPPORT ELBOW MID X MACHINE SCREWFIGURE 1.15 CONDENSATE DRAIN LINE ASSEMBLY PN 980241 Rev BWC - 12/07 Manufacturer of Hydronic Heating ProductsP.O. Box 14818 3633 I. Street Philadelphia, PA