Manuals / Crown Boiler / Household Appliance / Boiler

Crown Boiler M600 6a CROWN CONCENTRIC 80/125 VENT COMPONENTS VENT OPTIONS 3,8

Models: M600

1 22

Download 22 pages 62.75 Kb

Page 10

TABLE 1.6a: CROWN CONCENTRIC 80/125 VENT COMPONENTS

TABLE 1.6a: CROWN CONCENTRIC 80/125 VENT COMPONENTS

(VENT OPTIONS 3,8)

				USED ON
	CROWN PN	DESCRIPTION	SIZE	VENT	COMMENTS
				OPTION #
	230527	90 DEGREE EL (STANDARD)	80/125mm	3,8

	230528	90 DEGREE EL (SWEEP)	80/125mm	3,8

	230526	45 DEGREE EL	80/125mm	3,8

	230517	19 1/2” STRAIGHT	80/125mm	3,8	CAN BE CUT

	230515	39” STRAIGHT	80/125mm	3,8	CAN BE CUT

	230518	39” STRAIGHT	80/125mm	3,8	MAY NOT BE CUT

	230519	78” STRAIGHT	80/125mm	3,8	MAY NOT BE CUT

	230525	TELESCOPING STRAIGHT	80/125mm	3,8	ADJUSTABLE FROM 12-1/2” TO 16-1/2

	230531	HORIZONTAL TERMINAL	80/125mm	3

	230532	VERTICAL TERMINAL	80/125mm	8	(NOTE #1)

	230533	FLAT ROOF FLASHING	80/125mm	8

	230535	SLOPED ROOF FLASHING	80/125mm	8	(NOTE #2)

	230530	SUPPORT ELBOW WITH	80/125mm	8	(NOTE #3)
	230530	CHIMNEY CHASE BRACKET	80/125mm	8	(NOTE #3)
		CHIMNEY CHASE BRACKET

	230536	SUPPORT BAND	80/125mm	3,8

Table 1.6a Notes:

1)Vertical terminal can be used with either of the roof ﬂashings listed beneath it.

2)Sloped roof ﬂashing suitable for roof angles between 25 and 45 degrees.

3)Used at base of vertical run inside unused masonry chimney.

TABLE 1.6b: CROWN CONCENTRIC100/150 VENT COMPONENTS

(VENT OPTIONS 8,9)

				USED ON
	CROWN PN	DESCRIPTION	SIZE	VENT	COMMENTS
				OPTION #

	230567	90 DEGREE EL (SWEEP)	100/150mm	4,9

	230565	45 DEGREE EL	100/150mm	4,9

	230560	19 1/2” STRAIGHT	100/150mm	4,9	CAN BE CUT

	230562	39” STRAIGHT	100/150mm	4,9	CAN BE CUT

	230561	39” STRAIGHT	100/150mm	4,9	MAY NOT BE CUT

	230563	78” STRAIGHT	100/150mm	4,9	MAY NOT BE CUT

	230564	TELESCOPING STRAIGHT	100/150mm	4,9	ADJUSTABLE FROM 12-1/2” TO 17-1/2

	230569	HORIZONTAL TERMINAL	100/150mm	4

	230570	VERTICAL TERMINAL	100/150mm	9	(NOTE #1)

	230571	FLAT ROOF FLASHING	100/150mm	9

	230572	SLOPED ROOF FLASHING	100/150mm	9	(NOTE #2)

	230568	SUPPORT ELBOW WITH	100/150mm	9	(NOTE #3)
	230568	CHIMNEY CHASE BRACKET	100/150mm	9	(NOTE #3)
		CHIMNEY CHASE BRACKET

	230573	SUPPORT BAND	100/150mm	4,9

Table 1.6b Notes:

1)Vertical terminal can be used with either of the roof ﬂashings listed beneath it.

2)Sloped roof ﬂashing suitable for roof angles between 25 and 45 degrees.

3)Used at base of vertical run inside unused masonry chimney.

8

Image 10

Crown Boiler M600 installation instructions 6a CROWN CONCENTRIC 80/125 VENT COMPONENTS VENT OPTIONS 3,8

Contents

BWC150/225 CONCENTRIC VENTING INSTALLATION INSTRUCTIONS Manufacturer of Hydronic Heating ProductsP.O. Box 14818 3633 I. Street Philadelphia, PA BWC SeriesPage C. Assembly of Crown Concentric Venting and Condensate Drain Table of ContentsB. Concentric Vent Adapter Kit Installation A. Concentric Vent System DesignA. Concentric Vent System Design Do not install a barometric damper or drafthood on this boilerConcentric Venting For BWC150 and BWC225 Do not attempt to mix components from different approved vent systems45 Elbow Uncut Terminal Section Do not install the vent terminal directly over windows or doorsExample 4 Permitted Terminals for Horizontal VentingTABLE 1.1 SUMMARY OF HORIZONTAL VENTING OPTIONS MINIMUMFIGURE 1.2 HORIZONTAL CONCENTRIC VENTING VENT OPTION 3,4 6 Permitted Terminals for Vertical VentingFIGURE 1.3c POSITIONING VENT TERMINAL UNDER OVERHANGS TABLE 1.5 SUMMARY OF VERTICAL VENTING OPTIONS TABLE 1.4 VENT/ AIR INTAKE FITTING EQUIVALENT LENGTHVENT TABLE 1.6a CROWN CONCENTRIC 80/125 VENT COMPONENTS VENT OPTIONS 3,8 TABLE 1.6b CROWN CONCENTRIC100/150 VENT COMPONENTS VENT OPTIONS 8,91 The Concentric Vent Adapter Kits include B. Concentric Vent Adapter Kit InstallationFIGURE 1.7 VERTICAL CONCENTRIC VENT SYSTEM VENT OPTION Descriptionh Replace and tighten the clamp on the vent collar FIGURE 1.8 CONCENTRIC VENT ADAPTER ASSEMBLYj Use the exposed holes to line up the air intake box and gasket 100/150 C. Assembly of Crown Concentric Venting80/125 230517d Make an insertion mark 1” from the male end of the outer pipe f Reinstall the inner pipe 3 Joining Pipeb Remove the plastic inner pipe by pulling it out from the female end FIGURE 1.10 CUTTING STRAIGHT PIPE4 Horizontal Terminal Installation FIGURE 1.11a JOINING CUTTABLE PIPE FIGURE 1.11b JOINING NON CUTTABLE PIPEFIGURE 1.12a DIMENSION “L”, HORIZONTAL TERMINAL FIGURE 1.12b CUTTING OUTER PIPE OF HORIZONTAL TERMINALFIGURE 1.12d COMPLETING HORIZONTAL TERMINAL INSTALLATION FIGURE 1.12c CUTTING INNER PIPE OF HORIZONTAL TERMINALFIGURE 1.13a DIMENSION “H” FIGURE 1.13c COMPLETING VERTICAL TERMINAL INSTALLATION FIGURE 1.13b CUTTING VERTICAL TERMINALOVER ORIGINAL OPENING UNUSED CHIMNEY SUPPORT ELBOW FROM BO ILER FIGURE 1.14 CHIMNEY CHASE INSTALLATIONVERTICAL TERMINAL FLAT ROOF FLASHING WEATHER TIGHT FLAT ROOF CHIMNEY CHASE BRACKET INCLUDED WITH SUPPORT ELBOW MID X MACHINE SCREWFIGURE 1.15 CONDENSATE DRAIN LINE ASSEMBLY P.O. Box 14818 3633 I. Street Philadelphia, PA Manufacturer of Hydronic Heating ProductsPN 980241 Rev BWC - 12/07