2.Pivot the ends of the axle up and down to check for binding. If the axle is binding, loosen the lock nuts (See Figure 14) until binding is eliminated.

PIVOT AXLE

ADJUSTMENT BOLTS

LOCK

 

 

A

 

 

 

 

NUT

 

 

 

 

 

 

A

 

 

 

LOCK

NUTS

FRAME AXLE

CHANNELPIVOT

AXLE

SECTION A-A

Figure 14

3.Grasping the ends of the pivot axle, attempt to move each end of the axle forward and rearward to check for side play between the axle and frame channel. If play is present, gradually tighten the lock nuts until play is minimized.

4.Repeat steps 2 and 3 until minimum play without binding is achieved.

5.Raise the front of the tractor, remove the jack stands, and lower the tractor to the ground. Remove the blocks from the rear wheels.

HYDROSTATIC NEUTRAL ADJUSTMENT

The following adjustments will be necessary if the tractor creeps forward or rearward when neither the forward nor reverse pedals are depressed.

Checking the Transmission Neutral Setting

To check and adjust the transmission neutral setting, proceed as follows:

1.Drive the tractor for approximately 5-10 minutes to warm up the transmission, then stop the engine and engage the parking brake.

WARNING

Place the tractor on a firm and level surface and chock the front wheels before raising the rear wheels from the ground. Use jack stands to support the rear of the tractor when raised.

2.Raise the rear of the tractor, so that the rear tires are at least one inch above the surface, and set it on jack stands. Make certain the jack stands are posi- tioned to balance the tractor and prevent tipping.

WARNING

The operator presence safety circuit will stop the engine if the seat is empty when the brake pedal is released. If an assistant is seated when adjusting the neutral setting, use extreme caution to prevent the tractor from tipping or rolling. Similar precautions should be taken with any other method of over-riding the safety circuit, such as placing a weight in the seat. Never operate the tractor with the safety circuit disabled.

3.Carefully start the tractor engine and release the parking brake. Observe both rear wheels for rotation in either direction.

4.If wheel rotation is observed, adjust the neutral setting as follows:

a.Disconnect the rear control rod from the control arm by removing the hairpin cotter from the pivot sleeve (Refer to Figure 15).

b.If wheel rotation stops when the rod is disconnected, check and readjust the control rod per the instructions below.

c.If wheel rotation continues, loosen the locknut securing the hex cap screw and centering spacer to the neutral bracket (See Figure 15).

d.If the rotation is in the forward direction, slide the centering spacer rearward until the wheels just begin to rotate in the reverse direction. Then slowly slide the spacer slightly forward until wheel rotation stops.

e.If the rotation is in the reverse direction, slowly slide the centering spacer slightly forward until rotation stops.

f.Carefully tighten the hex cap screw and locknut, making certain the centering spacer does not move.

g.Stop the engine and engage the parking brake.

20

Page 19 Page 21
Page 20
Image 20
Cub Cadet 2206 manual Hydrostatic Neutral Adjustment, Checking the Transmission Neutral Setting
Page 19 Page 21

2206 specifications

The Cub Cadet 2206 is a versatile and robust lawn tractor designed for residential lawn care enthusiasts. It represents the perfect blend of power, precision, and convenience, making it an essential tool for maintaining a pristine landscape.

At the heart of the Cub Cadet 2206 is a reliable Kohler 20 HP engine. This powerful engine provides ample torque and acceleration, enabling users to tackle even the toughest mowing tasks with ease. The engine is built with durability in mind, ensuring long-lasting performance and reduced maintenance concerns.

One of the standout features of this lawn tractor is its 46-inch cutting deck, which allows users to cover large areas quickly while achieving a clean, manicured look. The cutting height is adjustable, providing the flexibility to customize grass length according to personal preferences or lawn care requirements. The deck is designed with a robust structure, ensuring it can withstand regular use while providing consistent results.

The Cub Cadet 2206 employs the innovative Automatic Transmission system that allows for smooth and effortless operation. This user-friendly system provides forward and reverse speeds without the need for manual shifting, making it ideal for navigating around obstacles and maneuvering in tight spaces. The ergonomic steering wheel and comfortable seat enhance the overall driving experience, reducing fatigue during extended mowing sessions.

When it comes to versatility, the Cub Cadet 2206 excels with its optional attachments. Gardeners can equip the tractor with various accessories such as baggers for grass clippings, snow blades for winter snow removal, and spreaders for fertilizing, making it an all-season asset. This adaptability ensures that homeowners can rely on their Cub Cadet throughout the year.

The machine also features a sturdy frame and high-traction tires, ensuring stability and grip on various terrains. This reliability is critical for maintaining control and safety while operating the tractor on sloped or uneven ground.

Additionally, the Cub Cadet 2206 is designed with user-friendly maintenance features. The easy-access oil filter and spacious engine compartment make routine upkeep significantly more manageable, contributing to the tractor's longevity and performance.

In summary, the Cub Cadet 2206 is an exceptional lawn tractor that combines power, comfort, and versatility. Whether you're mowing a small yard or a larger landscape, this machine's advanced features and user-centric design make lawn care a straightforward and enjoyable task. With proper maintenance and care, the Cub Cadet 2206 can be a reliable partner in keeping your outdoor space looking its best for years to come.
Top Page Image Contents