•If not already attached, slip the cables that run from the handle panel to the chute into the cable guide located on top of the engine. See Figure 4.

Cable Guide

Figure 4

•Unwrap the headlight wire which is attached to the headlight, beneath the handle panel. Wind the headlight wire around the right handle until excess slack is removed.

•Plug the wire from the headlight into the wire lead coming from the right side of the engine, beneath the fuel tank.

Final Adjustments

Auger Control Adjustment

Check the adjustment of the auger control as follows:

•Push forward on the auger control (Refer to Figure 7) until the small rubber bumper contacts the upper handle. There should be slack in the cable.

•Release the auger control. The cable should be straight. Make certain you can depress the auger control against the left handle completely.

If adjustment is necessary, proceed as follows:

•Loosen the jam nut and thread the cable in (for less slack) or out (for more slack) as necessary. See Figure 5.

“Z” End

Jam Nut

Auger Control Cable

Figure 5

•Recheck the adjustment before retightening the jam nut against the cable.

Skid Shoe Adjustment

The space between the shave plate and the ground can be adjusted by repositioning the skid shoes found on either side of the snow throwers auger housing. For close snow removal, place skid shoes in the low position. Use middle or high position when area to be cleared is uneven. See Figure 6.

Hex Nuts

Skid Shoes

Figure 6

IMPORTANT: It is NOT recommended that this snow thrower be operated on a gravel surface, as loose stones can be easily picked up and thrown by the machine. If you must operate on a gravel surface, ALWAYS adjust the skid shoes into the HIGH position to allow the shave plate maximum clearance.

Adjust skid shoes as follows:

•Loosen, but do NOT remove, the three hex nuts which fasten the skid shoe to the auger housing.

•Raise or lower the skid shoe to desired position.

NOTE: Make certain the entire base of both skid shoes is against the ground to avoid uneven wear on the skid shoes. When one side does wear out, the skid shoes are reversible.

•Retighten the hex nuts loosened earlier.

•Repeat this adjustment on the skid shoe found on the opposite side of the snow thrower.

Tire Pressure Adjustment

The tires are over-inflated for shipping purposes. Check tire pressure and reduce to between 15 psi and 20 psi.

NOTE: If the tire pressure is not equal in both tires, the unit may pull to one side or the other.

6

Page 5 Page 7
Page 6
Image 6
Cub Cadet 724WE manual Final Adjustments, Auger Control Adjustment, Skid Shoe Adjustment, Tire Pressure Adjustment
Page 5 Page 7

724WE specifications

The Cub Cadet 724WE stands out as a premium snow blower, designed to handle heavy snowfall with ease. Equipped with a powerful 243cc OHV engine, this machine delivers efficient performance, ensuring that even the most stubborn snow can be cleared away effectively. The engine provides consistent power and reliability, making it an ideal choice for homeowners who face harsh winter conditions.

One of the key features of the Cub Cadet 724WE is its innovative, track-driven design. This unique system offers enhanced stability and maneuverability, allowing users to navigate through deep snow and over uneven surfaces without losing control. The tracked design helps maintain traction, making it easier to push through heavy accumulations of snow.

The 724WE also boasts a wide 24-inch clearing width and a high 21-inch intake height, allowing it to tackle large areas in less time. This means fewer passes and more time saved during snow removal operations. Additionally, the machine is equipped with a steel auger that ensures effective snow collection and a strong impeller for efficient discharge.

Another notable feature of the Cub Cadet 724WE is its adjustable chute. The 2-way joystick control allows for easy direction adjustments, letting users throw snow up to 40 feet away, while also providing the flexibility to control the angle of the chute. This ensures that snow can be directed precisely where needed, preventing it from piling up in unwanted areas.

For added convenience, the 724WE includes LED headlights that enhance visibility during nighttime and early morning snow-clearing tasks. This feature allows users to work safely in low-light conditions.

User comfort is also a priority with the Cub Cadet 724WE. The machine features ergonomic hand grips and a padded handle, reducing user fatigue during operation. The electric start capability simplifies the startup process, enabling users to start their snow blower with the push of a button, even in frigid temperatures.

In summary, the Cub Cadet 724WE is a robust snow blower equipped with advanced features and technologies that make winter clearing tasks more manageable and efficient. Its power, track-driven stability, and user-friendly design make it a worthy investment for anyone looking to conquer winter's worst. With its high performance and innovative features, the 724WE ensures that your driveway and walkways stay clear all season long.
Top Page Image Contents