Cub Cadet Tank S S7232D Controls and Features

Controls and Features 4

Roll-Over
Protection	Power
System
	Implement
	Lift

Fuel Gauge

Fuel Tank

Fuel Tank Cap

PTO Switch

	R					THIS MACHINE IS EQUIPPED WITH A ROLL
		REVERSE				OVER PROTECTIVE SYSTEM (ROPS)
						YOUR SEAT BELT
						• SECURELY FASTEN
						BEFORE USE.
						• ALWAYS WEAR THE
Tachometer/						SEAT BELT WHEN THE
						• WHERE POSSIBLE, AVOID OPERATING THE MACHINE NEAR
						R OPS IS LOCKED IN
						PLACE UPRIGHT.
						• DO NOT WEAR SEAT BELT WHEN ROPS IS DOWN, I.E. NOT
		RUN				LOCKED UPRIGHT.
						• DO NOT MODIFY, REPAIR, OR REMOVE ANY ROPS
		OFF				COMPONENTS INCLUDING SEAT BELTS.
Hour Meter			START	FAST	SLOW	TURNING, OPERATING
						• STAY OFF SLOPES
						DITCHES, EMBANKMENTS, AND HOLES.
						• REDUCE SPEED WHEN
						ON SLOPES, AND ON
						R OUGH, SLICK, OR
	FORWARD					MUDDY SURFACES.
		STARTING INSTRUCTIONS				TOO STEEP FOR
	F	• To START, PARK BRAKE must be set, push down to latch.				S AFE OPERATION.
		• P.T.O. switch in OFF (down) position.				• WATCH WHERE YOU ARE GOING, ESPECIALLY ON SLOPES, WHEN
		• Foot pedals in NEUTRAL. Set Throttle properly.				TURNING, AND MANEUVERING AROUND OR UNDERNEATH OBSTACLES.
		• Turn key to ON, wait for GLOW PLUG light to go out,
		then START, release when engine runs.
Indicator		Ignition
Lights				Throttle Control
		Switch

Deck Height

Index

Cup Holder	•• AVOIIF D SUDDEN TURNS.
	AVOID SERIOUS INJURY OR DEATH
	• READ THE OPERATOR'S MANUAL, BEFORE USING THE MACHINE.	IMPLEMENT LIFT
	• GO ACROSS, NOT UPAND DOWN SLOPES.
	MACHINE STOPS GOING UPHILL, STOP BLADES AND BACK DOWN SLOWLY.
	• DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.
	• NEVER CARRY CHILDREN EVEN WITH BLADES OFF.
	• KEEP SAFETY DEVICES (GUARDS, SHIELDS, SWITCHES, ETC.)
	IN PLACE AND WORKING.
	• LOOK DOWN AND BEHIND BEFOREAND WHILE BACKING.
	• REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADES.
	• DO NOT OPERATE UNIT WHERE IT COULD SLIP OR TIP.
	• KNOW LOCATION AND FUNCTION OFALL CONTROLS.	STOPTO PUSH	PUSHLOCK,TO PUSH RELEASETO	EAKBR
	SERVICING.
	• BE SURE BLADES AND ENGINE ARE STOPPED BEFORE PLACING HANDS
	OR FEET NEAR BLADES.
	• BEFORE LEAVING OPERATOR POSITION, DISENGAGE BLADES, LET SPEED PEDAL
	RETURN TO NEUTRAL, ENGAGE PARKING BRAKE, SHUT OFF AND REMOVE KEY.
	• WHEN USING THE OPTIONAL GRASS BAGGING ATTACHMENT, THE FRONT
	COUNTER WEIGHT INCLUDED WITH BAGGER MUST BE INSTALLED.
	• DO NOT ADD FUEL WHILE THE ENGINE IS HOT OR RUNNING.
	• STOP ENGINE, DISCONNECT SPARK PLUG(S) BEFORE ADJUSTING OR
	• SLOW DOWN AND USE CAUTION ON SLOPES, 15º DEGREES MAX.

Brake Pedal/

Parking Brake

Forward Speed

Control Pedal

Reverse Speed

Control Pedal

Figure 4-1

NOTE: References to LEFT, RIGHT, FRONT, and REAR indicate that position on the tractor when facing forward while seated in the operator’s seat.

Deck Height Index

The deck height index consists of several holes located on the front/right of the foot platform. Each hole corresponds to a 1⁄4” change in the deck height position ranging from 1” at the lowest notch to 5” at the highest notch.

Power Implement Lift

The power implement lift is located on the LH console to the left of the operator’s seat, and is used to raise and lower the mower deck.

To raise the mowing deck to the transport position, place the clevis pin on the deck height index in the furthest hole from you and secure with the cotter pin and then use the power implement lift. To lower the deck, remove the clevis pin and reinsert it in the desired cutting height and secure with cotter pin and then use the power implement lift.

Seat Adjustment Levers (Not Shown)

The levers allow for adjustment of the operator’s seat. Refer to the Assembly & Set-Up section for instructions on adjusting the seat.

Cup Holder

The cup holder is located toward the rear of the LH console to the left of the operator’s seat.

14