5.Brush Guards and canopies can afford additional protection for the operator. The Brush Guard can deflect tree limbs, clothes lines, and other obstacles that otherwise could come in contact with the ROPS and OPDs. Contact of ROPS and OPDs by items such as tree limbs, clothes lines, guy wires, and buildings, could create hazardous conditions whereby the machine could experience a tip- over or
6.The ROPS and seat belt are integral parts of this machine and should not be tampered with, modified in any manner, or removed.
7.The ROPS extends above and behind the operator position, and therefore the operator must be aware of potential contact of the ROPS with items such as trees, buildings, doorways, clothes lines, utility wires, etc., that could cause the machine to upset or rollover. Use caution in (or avoid) areas where the ROPS could come in contact with any structures, trees, etc.
8.The ROPS and seat belt add additional mass that elevates the machine’s Center of Gravity (C.G.) which negatively affects the machine’s stability and traction. Use extra caution when operating on slopes.
9.Inspect the ROPS and seat belt assemblies on a regular basis for damage and improper operation. Replace all components that are damaged or are not functioning properly with authorized replacement parts.
10.Failure to use the seat belt properly could result in serious injury or death if an accidental overturn occurs. In order for the ROPS to be effective, the seat belt must be securely fastened around the operator at all times when the operator is on the machine. Contact with the ROPS during an overturn could cause serious injury or death.
11.The ROPS will not prevent the machine from upsets or roll overs.
12.Only approved attachments should be used on this machine.
Hydraulic Devices and Systems
Hydraulic fluid escaping under pressure may have sufficient force to penetrate skin and to cause serious injury. If foreign fluid is injected into the skin, it must be surgically removed within a few hours by a doctor familiar with this form of injury, or gangrene
may result.
Warning: Keep body and hands away from pinholes or nozzles that could eject hydraulic fluid under high pressure. Use paper or cardboard, not hands, to search for leaks!
Safely relieve all pressure in the system before performing any work on the system, and make sure that:
•The ignition switch is OFF
•The key is removed
•The engine spark plug wire(s) removed
•All connections to the negative terminal of the battery are removed
•The park brake is set
•All
•Hydraulic controls are actuated to release pressure on pumps, cylinders, etc. If “float” positions are available, they should be used.
After the above operations are completed, it should be safe to begin disconnecting the lines or components. It is still a good idea to cover the connection with a cloth shield and then gently
loosen connections.
Warning: Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the system.
Service
Related to Fuel
1.Fuel is highly flammable and its vapors can explode if ignited. Please respect it.
2.Do not smoke or permit others to smoke while handling fuel.
3.Always use approved containers for fuel and fill slowly to decrease the chance of static electricity buildup and spillage.
4.Store fuel in well ventilated and unoccupied buildings away from sparks and flames.
5.When dispensing fuel into approved containers, place the container on the ground when refueling to avoid a possibel static electricity ignition of fuel vapors.
6.Do not fill containers while it is inside a vehicle, trunk, bed of a pickup or floor of the trailer.
7.Always shut off the engine and permit it to cool before removing the fuel tank cap.
8.Always fill the fuel tank outdoors.
9.If the fuel container spout will not fit inside the fuel tank opening, use a funnel.
10.When filling the fuel tank, stop when the fuel reaches one inch from the top. The space is necessary for tank expansion. DO NOT OVERFILL.
11.Wipe up any spilled fuel.
General Service
1.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless, and deadly gas.
2.Before cleaning, repairing, or inspecting, make certain the blade(s) and all moving parts have stopped. Disconnect the spark plug wires and remove the key from the ignition to prevent unintended starting.
3.Periodically check to make sure the blades come to complete stop within approximately (5) five seconds after operating the blade disengagement control. If the blades do not stop within the this time frame, your machine should be serviced.
6Section 2 — Important Safe Operation Practices