Cypress CY62137EV30 manual Maximum Ratings, Electrical Characteristics Over the Operating Range

CY62137EV30 MoBL®

Maximum Ratings

(Above which the useful life may be impaired. For user guide- lines, not tested.)

Storage Temperature	–65°C to + 150°C
Ambient Temperature with
Power Applied	–55°C to + 125°C
Supply Voltage to Ground
Potential	–0.3V to 3.9V (VCC(MAX) + 0.3V)
DC Voltage Applied to Outputs
in High-Z State[4, 5]	–0.3V to 3.9V (V	CC MAX	+ 0.3V)

Electrical Characteristics Over the Operating Range

DC Input Voltage[4, 5]	–0.3V to 3.9V (VCC MAX + 0.3V)
Output Current into Outputs (LOW)		20 mA
Static Discharge Voltage		> 2001V
(per MIL-STD-883, Method 3015)
Latch-up Current		> 200 mA
Operating Range
	Ambient	VCC[6]
Device	Range Temperature

CY62137EV30-45LL Industrial –40°C to +85°C 2.2V to 3.6V

			Test Conditions						45 ns
Parameter	Description							Min.	Typ.[7]	Max.	Unit
VOH	Output HIGH Voltage		IOH = –0.1 mA				VCC = 2.20V	2.0			V
			IOH = –1.0 mA				VCC = 2.70V	2.4			V
VOL	Output LOW Voltage	IOL = 0.1 mA					VCC = 2.20V			0.4	V
			IOL = 2.1mA				VCC = 2.70V			0.4	V
VIH	Input HIGH Voltage		VCC = 2.2V to 2.7V					1.8		VCC + 0.3	V
			VCC= 2.7V to 3.6V					2.2		VCC + 0.3	V
VIL	Input LOW Voltage	VCC = 2.2V to 2.7V						–0.3		0.6	V
			VCC= 2.7V to 3.6V					–0.3		0.8	V
IIX	Input Leakage Current	GND < VI < VCC						–1		+1	∝A
IOZ	Output Leakage		GND < VO < VCC, Output Disabled					–1		+1	∝A
	Current
ICC	VCC Operating Supply		f = fMAX = 1/tRC				VCC = VCCmax		15	20	mA
	Current						IOUT = 0 mA
			f = 1 MHz						2.0	2.5
							CMOS levels
ISB1	Automatic CE			1 > VCC – 0.2V, CE2 < 0.2V					1	7	∝A
			CE
	Power-down Current		VIN > VCC			– 0.2V, VIN < 0.2V)
	— CMOS		f = fMAX		(Address and Data Only),
	Inputs		f = 0 (OE and WE), VCC = 3.60V
ISB2	Automatic CE			1 > VCC – 0.2V or CE2 < 0.2V,					1	7	∝A
			CE
	Power-down Current		VIN > VCC			– 0.2V or VIN < 0.2V,
	— CMOS Inputs		f = 0, VCC			= 3.60V

Notes:

4.VIL(min.) = –2.0V for pulse durations less than 20 ns.

5.VIH(max)=VCC+0.75V for pulse durations less than 20ns.

6.Full Device AC operation assumes a 100 ∝s ramp time from 0 to Vcc(min) and 200 ∝s wait time after VCC stabilization.

7.Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ.), TA = 25°C.

Document #: 38-05443 Rev. *B Page 3 of 12

[+] Feedback