Care and Cleaning

Cleaning the Optional Side Burners

important

•Cover the side burners with the included stainless steel burner cover when they are not in use and cool. Doing so will protect them and help keep them clean.

•The igniter will not work properly if the burner cap, burner head, burner base or the igniter itself are not clean. A dirty or wet igniter may not spark at all. Keep the igniters clean and dry to reduce this problem and avoid unnecessary service calls.

1.Remove the grate and disassemble the side burners underneath for cleaning as shown. After disassem- bling them, check for any dirt or grime deposited on the individual parts, including the igniters.

Cleaning the Exterior

Knobs and Trim Rings

caution

 

 

• Do not soak the knobs in water or put them in a

 

 

 

dishwasher.

 

 

 

• Do not remove the trim rings from the appliance.

 

 

 

Clean only the outside edges of the trim rings. If you

 

 

 

get moisture inside the trim rings, damage to the

 

 

 

electronic components can occur.

 

 

 

• Do not expose the knobs to hot objects, intense heat

 

 

 

or direct flame. Damage may result.

 

•

Wash the knobs regularly with a solution of warm

 

 

 

soapy water. Dacor recommends hand dishwashing

 

 

 

liquid.

 

•

Turn the knobs to the off position to remove them for

 

2.Brush completely around the igniter, including over and under the edge of the metal top and porcelain base. A stiff toothbrush is ideal for this task. Use care while cleaning because the porcelain igniter base is fragile and can crack or break. Do not use water to clean the igniters. If neces- sary, use a small amount of rubbing alcohol to help dissolve grime.

Burner cap

Burner head

Igniter

 

cleaning or replacement.

•

Grasp each knob and pull straight back, off of the

 

valve shaft.

•

Clean the outside edges of the trim rings while the

 

knobs are removed. Wipe them with a soft damp rag.

• To replace the knobs, align the “D-shaped” opening on the back

of the knob with the end of the valve shaft. Carefully push the knob on until it stops.

3. Examine the burner caps.

Burner base

Remove anything stuck in

 

the holes with a straight-

 

ened paper clip, wire or needle. Be careful not to

scratch or damage it. Do not distort the shape of the

holes.

 

4.Clean the burner cap and head with window cleaner or rubbing alcohol. Use a cleaning brush with plastic bristles or a firm tooth brush. When done, rinse the parts well with clean water. Dry the parts thoroughly before re-assembling them.

5.Test the burners after re-assembly. If the flame is uneven, be sure that the brass burner cap and the burner head are properly positioned. Check for any dirt or grime in the burner cap. If erratic clicking is still present, make sure the igniter is completely dry. If the unit still exhibits problems after drying, call your local Dacor Authorized Service Agent.

Exterior Stainless Steel Surfaces, Chrome and Other Metal Surfaces

caution

•Always wipe stainless steel (silver colored) surfaces with the grain.

•To prevent scratching, do not use abrasive cleaners or scrubbers on stainless steel or other metal surfaces.

•Clean the exterior stainless steel surfaces with the Dacor Stainless Steel Cleaner included with your appliance. Use it according to the directions on the package. See the Parts and Accessories section to order additional cleaner.

•You may also use a mild solution of detergent and warm water on stainless steel surfaces. Rinse and dry with a soft, lint-free cloth.

•To clean other metal surfaces, use a soft cloth with a mild solution of detergent and warm water. Rinse and dry with a soft, lint-free cloth.

19