FIG.01 Natural Gas

GAS REQUIREMENTS

Verify the type of gas supply to be used, either

 

 

 

natural or LP, and make sure the marking on the

 

 

 

appliance rating plate agrees with that of the

 

 

 

supply. The rating plate is located on the inside

 

 

 

back wall of the Grill. Never connect an

 

Bottom of unit

 

 

 

 

unregulated gas line to the appliance.

 

Coupling

Threading compound

 

 

 

 

 

 

 

1/2 NPT

must be resistant to LP gas

An installer supplied gas shut-off valve must be

 

 

Close

 

 

installed in an easily accessible location.

All

NIpple

 

 

Regulator

 

 

 

 

 

 

installer supplied parts must conform to local

4.0" W.C.

 

1/2 NPT

 

 

Close

codes, or in the absence of local codes, with the

Adapter 1/2 NPT

 

 

NIpple

 

 

 

 

National Electrical Code, ANSI/NFPA 70 or the

to 3/8 flare fitting

 

 

Do not put threading

 

Installer supplied shut-off

 

 

 

Canadian Electrical Code, CSA C22.1, and

the

 

valve must be easily

compound on these

 

 

accessible*

National Fuel Gas Code, ANSI Z223.1

or

threads

 

 

 

 

 

CAN/CGA-B149.1 Natural Gas Installation Code

*Installation must conform with local

 

codes or with the National Fuel Gas

 

or CAN/CGA-B149.2 Propane Installation Code.

Code ANSI Z223.1 or the CAN/CGA-

 

B149.2 Propane Installation Code

 

All pipe sealants must be an approved type and resistant to the actions of LP gases. Never use

pipe sealant on flare fittings. All gas connections should be made by a qualified technician and in accordance with local codes and ordinances. In the absence of local codes, the installation must comply with the national fuel gas code ANSI Z223.1. Gas conversion kits are available from the factory. When ordering gas conversion kits have the model number, and the type of gas (natural or LP) from your grill.

TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:

BGB30-BQR - 50,0 00 Btu/hr

The appliance and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.) The appliance must be isolated from the gas supply piping system by closing its individual manual shut- off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The installation of this appliance must conform with local codes or, in the absence of local codes, with the national fuel gas code, ANSI Z223.1. Installation in Canada must be in accordance with the Standard CAN/CGA-B149.2 Propane Installation Code and local codes.

NATURAL GAS HOOK UP: (This type of connection should be performed by a certified or licenced technician only.)

Connection: 1/2" NPT male with 3/8" flare adapter. Operating pressure: 4.0" W.C.

Supply pressure: 5" to 14" water column. If in excess of 14" W.C. a step down regulator is required. Check with your local gas utility company or with local codes for instructions on installing gas supply lines. Be sure to check on type and size of run, and how deep to bury the line. If the gas line is too small, the grill will not function properly. Any joint sealant used must be an approved type and be resistive to the actions of LP gases.

TO HOOK-UP THE FITTINGS SUPPLIED WITH THE GRILL:

Assemble as shown (Fig.01). Use threading compound on male threads only. Do not use threading compound on the male end of the 1/2 NPT to 3/8 flare adapter. Use a second pipe wrench to hold the grill inlet pipe to avoid shifting any internal gas lines of the grill. Ensure that the regulator arrow points in the direction of gas flow towards the unit, away from the supply. Do not forget to place the installer supplied gas valve in an accessible location.

7

Page 7 Page 9
Page 8
Image 8
DCS BGB30-BQR manual GAS Requirements, Total GAS Consumption of the Grill with ALL Burners on HI
Page 7 Page 9

BGB30-BQR specifications

The DCS BGB30-BQR is a state-of-the-art gas monitoring and detection system, designed to ensure maximum safety and reliability in a variety of industrial environments. This advanced device integrates cutting-edge technologies and sophisticated features that make it a preferred choice for professionals in sectors such as oil and gas, manufacturing, and chemical processing.

At the heart of the BGB30-BQR lies its high-performance gas sensors, which are capable of detecting a wide range of hazardous gases including methane, propane, and hydrogen sulfide. These sensors utilize advanced electrochemical technology that allows for quick and accurate readings, ensuring that any potential gas leaks can be identified rapidly. The device is designed for real-time monitoring, providing continuous data to maintain safety in critical settings.

One of the standout features of the BGB30-BQR is its robust wireless communication capabilities. Equipped with built-in Bluetooth and Wi-Fi, the system allows for seamless integration into existing network infrastructures. This feature enables operators to access real-time data remotely via smartphones or tablets, empowering them to make informed decisions instantly. Additionally, the BGB30-BQR supports both local and cloud-based data storage, ensuring that historical data is available for analysis and regulatory compliance.

The BGB30-BQR is also built with durability in mind. Its rugged design meets tough environmental standards, making it suitable for both indoor and outdoor applications. With an IP68 rating, the device is resistant to dust and water ingress, ensuring longevity in challenging conditions.

Another significant characteristic of the BGB30-BQR is its user-friendly interface. The device comes with an intuitive LCD display that shows real-time gas level readings, battery status, and alerts for immediate troubleshooting. Furthermore, the device includes customizable alarm settings that can be tailored to suit specific operational requirements, ensuring prompt responses to any sign of danger.

In conclusion, the DCS BGB30-BQR gas monitoring system exemplifies innovation in safety technology. With its advanced sensing capabilities, robust communication features, durable construction, and user-friendly design, it stands out as a reliable solution for gas detection in various industrial applications. Investing in the BGB30-BQR not only enhances workplace safety but also boosts operational efficiency by providing critical data when it matters most.
Top Page Image Contents