GRILL BURNER ADJUSTMENTS

Grill Burner Air Adjustment:

Each grill burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas supply or a conversion from one gas to another may make it necessary to adjust the burners. The flames of the burners (except the rotisserie burner) should be visually checked and compared to that of the drawing in Fig.07 and Fig. 09. Flames should be blue and stable with no yellow tips, excessive noise or lifting. If any of these conditions exist, check if the air shutter or burner ports are blocked by dirt, debris, spider webs, etc. Proceed with air shutter adjustment. The amount of air which enters a burner is governed by a sheet metal cup at the inlet of the burner called an air shutter. It is locked in place by a set screw which must be loosened prior to lighting the burner for adjustment.

Note: Side burner has no flame adjustment.

To Adjust:

1.Be careful as the burner may be very hot.

2.If the flame is yellow, indicating insufficient air, turn the airshutter counterclockwise to allow more air to the burner.

3.If the flame is noisy and tends to lift away from the burner, indicating too much air, turn the air shutter clockwise.

4.Once adjusted turn the burner off and reverse steps to reassemble.

LOW SETTING ADJUSTMENTS:

The valves on the grill feature an adjustable low setting. Due to fluctuations in gas pressure, heating value or gas conversion, you may feel it necessary to increase or

decrease gas flow in the low position. We do not recommend adjusting the infrared rotis burner.

To Adjust:

1. Light the burner.

2. Turn the control knob to the lowest setting (all the way counter-clockwise).

3. Remove the knob.

4. While holding the valve shaft with pliers, insert a thin, flat

tipped screwdriver into the shaft and while viewing the

FIG.10 Low Setting Adjustment

 

burner adjust to a minimum stable flame (Fig. 10).

 

WARNING: IMPORTANT!

Before lighting, inspect the gas supply piping or hose prior to turning the gas "on". If there is evidence of cuts, wear, or abrasion, it must be replaced prior to use.

14

Page 14 Page 16
Page 15
Image 15
DCS BGB30-BQR manual Grill Burner Adjustments, Grill Burner Air Adjustment, To Adjust, LOW Setting Adjustments
Page 14 Page 16

BGB30-BQR specifications

The DCS BGB30-BQR is a state-of-the-art gas monitoring and detection system, designed to ensure maximum safety and reliability in a variety of industrial environments. This advanced device integrates cutting-edge technologies and sophisticated features that make it a preferred choice for professionals in sectors such as oil and gas, manufacturing, and chemical processing.

At the heart of the BGB30-BQR lies its high-performance gas sensors, which are capable of detecting a wide range of hazardous gases including methane, propane, and hydrogen sulfide. These sensors utilize advanced electrochemical technology that allows for quick and accurate readings, ensuring that any potential gas leaks can be identified rapidly. The device is designed for real-time monitoring, providing continuous data to maintain safety in critical settings.

One of the standout features of the BGB30-BQR is its robust wireless communication capabilities. Equipped with built-in Bluetooth and Wi-Fi, the system allows for seamless integration into existing network infrastructures. This feature enables operators to access real-time data remotely via smartphones or tablets, empowering them to make informed decisions instantly. Additionally, the BGB30-BQR supports both local and cloud-based data storage, ensuring that historical data is available for analysis and regulatory compliance.

The BGB30-BQR is also built with durability in mind. Its rugged design meets tough environmental standards, making it suitable for both indoor and outdoor applications. With an IP68 rating, the device is resistant to dust and water ingress, ensuring longevity in challenging conditions.

Another significant characteristic of the BGB30-BQR is its user-friendly interface. The device comes with an intuitive LCD display that shows real-time gas level readings, battery status, and alerts for immediate troubleshooting. Furthermore, the device includes customizable alarm settings that can be tailored to suit specific operational requirements, ensuring prompt responses to any sign of danger.

In conclusion, the DCS BGB30-BQR gas monitoring system exemplifies innovation in safety technology. With its advanced sensing capabilities, robust communication features, durable construction, and user-friendly design, it stands out as a reliable solution for gas detection in various industrial applications. Investing in the BGB30-BQR not only enhances workplace safety but also boosts operational efficiency by providing critical data when it matters most.
Top Page Image Contents