Manuals / Brands / Power Tools / Lathe / Delta / Power Tools / Lathe

Delta 46-715 instruction manual OPERATION

1 24

Download 24 pages, 1.17 Mb

10

ADJUSTING CLAMP ON TOOL REST

To adjust the tool rest clamping action, use a 15/16" wrench to adjust the nut (A) Fig. 16 in the same manner as the headstock and

tailstock.

ATTACHING ON/OFF SWITCH TO TOOL

The "ON/OFF" switch comes unattached to the tool to protect it from damage in shipping. To attach the "ON/OFF" Switch:

1. Remove the two hex bolts (A) Fig. 19 that are attached to the back of the headstock, located near the top.

2. Align the two holes in the bottom of the "ON/OFF" switch with the two holes where the hex bolts were removed in STEP 1.

3. Secure the "ON/OFF" switch to the headstock with the bolts that were removed in STEP 1(Fig. 20).

A

C

D

C

STARTING AND STOPPING THE TOOL

The power switch (A) Fig. 22, located under the safety cover (B) Fig. 21, provides electrical power to the adjustable speed drive.

Lift the safety cover (B) and move the switch up to the “ON” position. To turn the power off, push the safety cover (B) down.

NOTE: In case of emergency, immediately push the safety cover (B)down to shut off power.

LOCKING SWITCH IN THE “OFF” POSITION

IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use, using a

padlock (C) Fig. 22, with a 3/16" diameter shackle inserted through the holes in the switch plate (D) Fig. 22B.

B

Fig. 17 Fig. 18

Fig. 19

Fig. 20

Fig. 21 Fig. 22

A

B

C

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

D

Fig. 22B

Contents

Main TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS SAFETY GUIDELINES - DEFINITIONS CALIFORNIA PROPOSITION 65 GENERAL SAFETY RULES ADDITIONAL SAFETY RULES FOR WOOD LATHES SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. FAILURETO FOLLOW THESE RULES MAY RESULTIN SERIOUS INJURY. POWER CONNECTIONS MOTOR SPECIFICATIONS GROUNDING INSTRUCTIONS Fig. D-1 This machine must be grounded while in use to protect the operator from electric shock. EXTENSION CORDS MINIMUM GAUGE EXTENSION CORD FUNCTIONAL DESCRIPTION CARTON CONTENTS UNPACKING AND CLEANING ASSEMBLY ASSEMBLY TOOLS REQUIRED ASSEMBLY TIME ESTIMATE ASSEMBLING THE STAND ATTACHING THE LATHE BED TO THE STAND HEADSTOCK SPUR CENTER TAILSTOCK LIVE CENTER ADJUSTING CLAMPS ON THE HEADSTOCK AND TAILSTOCK TOOL REST ADJUSTING CLAMP ON TOOL REST OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS ACTIVATING THE SPINDLE CHANGING SPEED RANGES ALIGNING THE HEADSTOCK CENTER TO THE TAILSTOCK CENTER MACHINE USE GLOSSARY LATHE TOOLS HOW TO TURN SPINDLES Fig. 27 CENTERING THE WORK Fig. 28 Fig. 29 Fig. 30 TOOL REST POSITION Fig. 32 Fig. 36 Fig. 37 Fig. 35 ROUGHING A CYLINDER SMOOTHING A CYLINDER USING THE PARTING TOOL SQUARING AN END Fig. 40 Fig. 41 Fig. 42 CUTTING A SHOULDER Fig. 43 Fig. 44 Fig. 45A Fig. 45B CUTTING SMALL BEADS Fig. 48 VEE GROOVES LONG CUTS Fig. 56 COVE CUTS Fig. 51 SQUARE SECTIONS Fig. 57 Fig. 58 Fig. 59 Fig. 60 Fig. 61 Fig. 62 MOUNTING THE WORKPIECE TO THE FACEPLATE INBOARD/OUTBOARD TURNING MAINTENANCE TROUBLESHOOTING KEEP MACHINE CLEAN FAILURE TO START LUBRICATION PARTS, SERVICE OR WARRANTY ASSISTANCE SERVICE Page WARRANTY Two Year Limited New Product Warranty Page The following are trademarks of PORTER-CABLE DELTA (Las siguientes son marcas registradas de PORTER-CABLE DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE PORTER-CABLE DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE DELTA) Delta ms cercano. Delta deben obtenerse ponindose en contacto con cualquier distribuidor Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service Center, or Porter-Cable