Delta 90513776 Additional Specific Safety Rules, USE only Blades of the Correct Size

ADDITIONAL SPECIFIC SAFETY RULES

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock, fire, and/or serious personal injury or property damage.

1.DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury.

2.OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety.

3.FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution.

4.SECURE THE MACHINE TO A SUPPORTING SURFACE. Vibration can possibly cause the machine to slide, walk, or tip over, causing serious injury.

5. USE ONLY CROSSCUT SAW BLADES. Use only zero-degree or negative hook angles when using carbide-tipped blades. Do not use blades with deep gullets. These can deflect and contact the guard, and can cause damage to the machine and/or serious injury.

6.USE ONLY BLADES OF THE CORRECT SIZE

AND TYPE specified for this tool to prevent damage to the machine and/or serious injury.

7.USE A SHARP BLADE. Check the blade to see if it runs true and is free from vibration. A dull blade or a vibrating blade can cause damage to the machine and/or serious injury.

8.INSPECT BLADE FOR CRACKS or other damage prior to operation. A cracked or damaged blade can come apart and pieces can be thrown at high

speeds, causing serious injury. Replace cracked or damaged blades immediately.

9.CLEAN THE BLADE AND BLADE FLANGES prior to operation. Cleaning the blade and flanges allows you to check for any damage to the blade or flanges. A cracked or damaged blade or flange can come apart and pieces can be thrown at high speeds, causing serious injury.

10.USE ONLY BLADE FLANGES specified for this tool to prevent damage to the machine and/or serious injury.

11.CLEAR THE AREA OF FLAMMABLE LIQUIDS and/or gas prior to operation. Sparks can occur that would ignite the liquids and cause a fire or an explosion.

12.CLEAN THE MOTOR AIR SLOTS of chips and sawdust. Clogged motor air slots can cause the machine to overheat, damaging the machine and possibly causing a short which could cause serious injury.

13.TIGHTEN THE TABLE CLAMP HANDLE and any other clamps prior to operation. Loose clamps can cause parts or the workpiece to be thrown at high speeds.

14.NEVER START THE TOOL with the blade against the workpiece. The workpiece can be thrown, causing serious injury.

15.KEEP ARMS, HANDS, AND FINGERS away from the blade to prevent severe cuts. Clamp all workpieces that would cause your hand to be in the “Table Hazard Zone” (within the red lines).

16.ALLOW THE MOTOR TO COME TO FULL SPEED prior to starting cut. Starting the cut too soon can cause damage to the machine or blade and/or serious injury.

17.WHEN USING A SLIDING MITER SAW AS A REGULAR MITER SAW, LOCK THE SLIDE MECHANISM IN PLACE. If the slide mechanism is not locked, the saw can kick back toward you.

18.NEVER REACH AROUND or behind the saw blade. A moving blade can cause serious injury.

19.NEVER CUT FERROUS METALS or masonry. Either of these can cause the carbide tips to fly off the blade at high speeds causing serious injury.

20.NEVER CUT SMALL PIECES. Cutting small pieces (where your hand would be within 6” of the saw blade) can cause your hand to move into the blade, resulting in serious injury.

21.NEVER LOCK THE SWITCH in the “ON” position. Setting up the next cut could cause your hand to move into the blade, resulting in severe injury.

22.NEVER APPLY LUBRICANT to a running blade. Applying lubricant could cause your hand to move into the blade, resulting in serious injury.

23.DO NOT PERFORM FREE-HAND OPERATIONS (wood that is not held firmly against the fence and table). Hold the work firmly against the fence and table. Free-hand operations on a miter saw could cause the workpiece to be thrown at high speeds, causing serious injury. Use clamps to hold the work when possible.

24.PROPERLY SUPPORT LONG OR WIDE WORK- PIECES. Loss of control of the workpiece can cause serious injury.

25.AFTER COMPLETING CUT, release power switch and wait for coasting blade to come to a complete stop before returning saw to raised position. A moving blade can cause serious injury.

26.TURN OFF THE MACHINE and allow the blade to come to a complete stop prior to cleaning the blade area or removing debris in the path of the blade. A moving blade can cause serious injury.

27.TURN OFF MACHINE and allow the blade to come to a complete stop before removing or securing workpiece, changing workpiece angle, or changing the angle of the blade. A moving blade can cause serious injury.

28.PROPERLY SUPPORT LONG OR WIDE WORK- PIECES. Loss of control of the workpiece can cause injury.

29.NEVER PERFORM LAYOUT, ASSEMBLY, OR SET-UP WORK on the table/work area when the machine is running. A sudden slip could cause a hand to move into the blade. Severe injury can result.

30.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use. Someone else might accidentally start the machine and cause injury to themselves.

31.BEFORE OPERATING THE SAW, check and securely lock the bevel, miter, and sliding fence adjustments.

32.THE CUTTING HEAD MUST RETURN QUICKLY TO THE FULL UP POSITION. Failure to do so will not allow the lower guard to operate properly and may result in personal injury. See manual section on “Adjusting the Cuttinghead Return”.

33.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertool institute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca,

IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

5