ADDITIONAL SAFETY RULES FOR

SCROLL SAWS

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1.DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions.

2.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.YOUR SCROLL SAW MUST be securely fastened to a stand or workbench. If there is any tendency for the stand or workbench to move during operation, the stand or workbench MUST be fastened to the floor.

5.THIS SCROLL SAW is intended for indoor use only.

6.MAKE SURE blade is properly tensioned before operating saw.

7.TO AVOID blade breakage ALWAYS adjust blade tension correctly.

8.MAKE SURE the blade teeth point downward toward the table.

9.NEVER turn the saw "ON" before clearing the table of all objects (tools, scraps of wood, etc.).

10.DO NOT cut material that is too small to be safely supported.

11.AVOID awkward hand positions where a sudden slip could cause a hand to move into the blade.

12.ALWAYS keep hands and fingers away from blade.

13.ALWAYS adjust holddown foot for each new operation.

14.DO NOT USE dull or bent blades.

15.DO NOT attempt to saw material that does not have a flat surface, unless a suitable support is used.

16.MAKE "relief" cuts before cutting long curves.

17.NEVER attempt to cut a curve that is too tight for the blade being used.

18.WHEN backing a blade out of a workpiece, the blade may bind in the saw kerf. This is usually caused by sawdust in the kerf. If this happens, turn "OFF" the switch and remove plug from power source outlet. Wedge open the kerf and back blade out of the workpiece.

19.THE USE of attachments and accessories not recommended by Delta may result in the risk of injuries.

20.ALWAYS hold the work firmly against the table.

21.DO NOT feed the material too fast while cutting. Only feed the material fast enough so that the blade will cut.

22.NEVER start the Scroll Saw with the stock pressed against the blade.

23.WHEN cutting a large workpiece MAKE SURE the material is supported at table height.

24.USE CAUTION when cutting material which is irregular in cross section which could pinch the blade before the cut is completed. A piece of moulding for example must lay flat on the table and not be permitted to rock while being cut.

25.USE CAUTION when cutting round material such as dowel rods or tubing. They have a tendency to roll while being cut causing the blade to "bite." Use a V-block to control the piece.

26.ALWAYS release blade tension before removing the blade from the upper or lower blade holders.

27.MAKE CERTAIN table tilting lock is tightened before starting the machine.

28.NEVER reach under the table while the machine is running.

29.NEVER perform layout, assembly or set-up work on the table while the saw is operating.

30.ALWAYS STOP the saw before removing scrap pieces from the table.

31.TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

32.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

33.ADDITIONAL INFORMATION regarding the safe and proper operation of this tool is available from the Power Tool Institute, 1300 Summer Avenue, Cleveland, OH 44115-2851. Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

3

Page 3
Image 3
Delta SS200 instruction manual Refer to them often Use them to instruct others, Additional Safety Rules for Scroll Saws