Denon AVR-1082 manual Setting the Digital In Assignment

ENGLISH

7	Select “Yes”.
	TUNING
BAND	MODE

When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level adjustment mode.

After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each surround mode on page 27.

8	a. If the “Auto” mode is selected:
	Test tones are automatically emitted from the different

speakers.

The test tones are emitted from the different speakers in the following order, at 4-second intervals the first time and second time around, 2-second intervals the third time around and on:

Flashing

1spkr

SB

FL	C	FR	SR	SBR	SBL	SL	SW
				2spkrs

Example: When the volume is set to

–12 dB while the test tone is being produced from the subwoofer

You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5/7 CH STEREO, DOLBY/DTS SURROUND, WIDE SCREEN, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO MOVIE, and MATRIX.

When using either surround speakers A or B, or when using surround speakers A and B at the same time, be sure to adjust the balance of playback levels between each channel for the various selections of “A or B” and “A and B”.

Setting the Digital In Assignment

•This setting assigns the digital input jacks of the AVR-3802 for the different input sources.

TUNING

BANDMODE

TUNING

TUNING

BANDMODE

TUNING

When the surround back speaker setting is set to “1spkr” for “Speaker Configuration”, this is set to “SB”.

Use the CURSOR buttons to adjust all the speakers to the same volume.

The volume can be adjusted between –12 dB and +12 dB in units of 1 dB.

b. When the “Manual” mode is selected

Use the CURSOR left and right to select the speaker for which you want to output test tones, then use the CURSOR up and down to adjust so that the volume of the test tones from the various speakers is the same.

Flashing

1	TUNING	At the System Setup Menu select “Digital In Assignment”.
	BAND	MODE
	TUNING
2	ENTER	Switch to the Digital In Assignment screen.
	SHIFT

TUNING

BAND	MODE	Example: When the volume is set to
		–12 dB while the
	TUNING	subwoofer is selected

9	ENTER	After the above settings are completed, press the ENTER button.
	SHIFT	The “Channel Level” screen reappears.

To cancel the settings, select “Level Clear” and “Yes” on the “Channel Level” screen, then make the settings again.

The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter at the listening position.

If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adjust for natural balance.

NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s own volume control.

3	TUNING			Select the digital input jack to be assigned to the input source.
			TUNING	• To select the input source
	BAND	BAND	MODE	• To select the digital input jack
		MODE
	TUNING		TUNING	Select “OFF” for input sources for which no digital input jacks are used.
				If “Yes” is selected for “Default”, the settings are automatically reset
				to the default values.
4	ENTER	Enter the setting.
	SHIFT	The System Setup Menu reappears.

NOTES:

•The OPTICAL 3 jacks on the AVR-3802’s rear panel are equipped with an optical digital output jack for recording digital signals on a CD recorder, MD recorder or other digital recorder. Use this for digital recording between a digital audio source (stereo - 2 channel) and a digital audio recorder.

•Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the AVR-3802’s rear panel to any jack other than the OPTICAL 3 IN jack.

•“PHONO” and “TUNER” cannot be selected on the Digital In Assignment screen.

14