Denon AVR-1082 manual Adjusting the sound quality Tone, Listening over headphones

ENGLISH

Playback using the external input (EXT. IN) jacks

After starting playback

1	Set the external input (EXT. IN) mode.
	Press the EXT. IN to switch the external input.
	EXT.IN
		EXT.IN
	(Main unit)	(Remote control unit)

Once this is selected, the input signals connected to the FL (front left), FR (front right), C (center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right) channels of the EXT. IN jacks are output directly to the front (left and right), center, surround (left and right) and surround back (left and right) speaker systems as well as the pre-out jacks without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SUBWOOFER jack.

2	Cancelling the external input mode
	To cancel the external input (EXT. IN) setting,
	press the input mode (AUTO, PCM, DTS) or
	ANALOG button to switch to the desired input
	mode. (See page 23.)
	AUTO	PCM	DTS	ANALOG
				MODE	ANALOG

B

2	1
	6.1 / 7.1	DIRECT	STEREO
	SURROUND
2		INPUT
	MODE	ANALOG	EXT.IN	1
	SYSTEM CALL
	CALL 1	CALL 2	BACKLIGHT

NOTES:

•In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be output from channels not connected to the input jacks.

•The external input mode can be set for any input source. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode.

[1]Adjusting the sound quality (TONE)

The tone control function will not work in the Direct mode.

1	The tone switches as follows each time the
	TONE CONTROL button is pressed.			B
	TONE
	CONTROL
	BASS	TREBLE
	(Main unit)
2				3	2 1
	With the name of the volume to		SELECT
	be adjusted selected, turn the
	SELECT knob to adjust the level.
			(Main unit)
	• To increase the bass or treble: Turn the control 3			If you do not want the bass and treble to be
				adjusted, turn on the tone defeat mode.
	clockwise. (The bass or treble sound can be
	increased to up to +12 dB in steps of 2 dB.)			TONE DEFEAT
				The signals	do not pass
	• To decrease the bass or	treble: Turn the
				through the bass and treble
	control clockwise. (The bass or treble sound			adjustment circuits, providing
	can be decreased to up to –12 dB in steps of			higher quality sound.
	2 dB.)			(Main unit)
[2]	Listening over headphones
1	Connect the headphones to		PHONES
	the PHONES jack of the front			B
	panel.

(Main unit) (Remote control unit)

•When the input mode is set to the external input (EXT. IN), the play mode (DIRECT, STEREO, DOLBY/DTS SURROUND, 5/7CH STEREO, WIDE SCREEN or DSP SIMULATION) cannot be set.

				1
2	Press the OUTPUT button to play the sound				1
	over the headphones only.
	TV/	0	+10		NOTE:
	VCR
	OUTPUT	PTY	RT	2	To prevent hearing loss, do not raise the volume level
	RDS
	TEST	SPEAKER	OUTPUT
	TONE				excessively when using headphones.
		SURROUND
	DOLBY/DTS	DSP	5CH / 7CH
	SURROUND	SIMU.	STEREO

•The output to the speaker and pre-out jacks is turned off and no sound is produced from the speakers.

Caution: Switching off the power of the unit and the unit will cancel the settings.

[3] Turning the sound off temporarily (MUTING)

1	Use this to turn off the audio	MUTING
	output temporarily.

Press the MUTING button.

Cancelling MUTING (Remote control unit)

mode.

Press the MUTING button again.

TUNING

+		+
SKIP	ENTER
-	SHIFT	-
SKIP	MUTING		1
TUNER	PHONO	CD

1 2 3

24