Denon AVR-3300 manual ENGLISH Learning function

CHANNEL

TV/VCR

A / B

DISC SKIP+

MASTER VOL.

MUTING

SURROUND

PARAMETER

MENU/GUIDE

ENGLISH

Learning function

•If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-3300’s remote control to “learn” the codes from the component’s original remote control.

•The buttons that can be “learned” are the CD, DECK and MD system buttons (see page 30) and the DVD, VDP, VCR and TV system buttons (see page 33). (For the CD, MD, DVD, VDP and TV, the A block buttons can also be “learned”, and for the DVD and TV, the B block buttons can

also be “learned”.)		START	LEARNED/TX	RC-860
	SYSTEM CALL		POWER
	SET	CALL	OFF	ON / SOURCE
	DVD	VDP	TUNER	SHIFT

1	Press the USE/LEARN selector button with the tip of a pen
	etc., to set the learn mode. Both the START and LEARNED/TX
	indicators flash.	Flashes

	1	2	3
A	TV/DBS		PHONO
	4	5	6
	VCR-1	CD	MD / TAPE
	7	8	9
	VCR-2/V.AUX
	+10	0

This unit’s remote control unit

VOLUME

DOLBY / DTS

SPEAKER SURROUND DIRECT

DSP SIMULATION	5CH STEREO	STEREO
INPUT MODE	ANALOG	EXT.IN

2	AUDIO		DECK	MD
			CD	MULTI
	AVR/AVC	VIDEO	DVD	TV
			VDP	VCR
			SYSTEM
	TUNING		SETUP

4

3

2	Set the program switch to the side to be learned.
	Set to the AUDIO side for the CD, tape deck or DAT position,
	to the VIDEO side for the VDP, VCR or TV position.
		AUDIO
		AVR/AVC				VIDEO
3	Set the program switch to the position to be learned.
			DECK	MD
	CD						MULTI
			DVD				TV
			VDP		VCR
4	Set the remote control units so they are facing each other,
	then press the button to be learned on this unit’s remote

control unit.

Transmitting windows	Other remote
	control unit
Light

Approx.

5 cm

This unit’s remote control unit

The indicator stops flashing and the START LED lights.

The learnable buttons are the buttons which can be operated with the DENON system codes for the CD player, DAT and tape deck, the buttons which can be operated with the preset memory for the VCR, VDP and TV. For the TV only, however, the buttons in the section indicated “A” on the diagram above can also be “learned”. Use these to “learn” TV channels.

TITLE

BAND

			CH SELECT	B
		MODE	ENTER
			SELECT
		MEMORY	STATUS	ON SCREEN
	1,8		DISPLAY	RETURN
		USE/LEARN T.TONE	MULTI OUTPUT	DVD
				SET UP
5	Check that the START LED is lit, then press the button to be
	“learned” on the other remote control unit.

Other remote control unit

	This unit’s remote
	control unit
6	Once the START LED turns off and the LEARNED/TX LED
	lights, release the button on the other remote control unit.

	The two LEDs start
	flashing again.	Light
7	To “learn” other buttons, repeat steps 2 to 6.
8	Once the learning operation is completed, press the
	USE/LEARN selector button again.
	The two LEDs stop flashing and	the learning mode is

cancelled.

Check that the stored codes work properly.

NOTES:

•Up to 26 codes can be “learned”, but this number may be lower if the codes are long.

•If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s) is released.

•If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes cannot be stored in RC-860.

•If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just attempted to store was not stored.

To “learn” that code, first perform the resetting operation. (See page 37.)

34