NOTE
•Do not disconnect the setup microphone until the auto setup procedure is completed.
•When using headphones, unplug the headphones before starting the auto setup procedure.
Auto SetupOptimize settings for speakers in use.
aStart Menu
The settings found at this stage are applied automatically.
GAuto setup flowH
Step 1: Speaker Detection
Step 2: Measurement
Step 3: Calculation
Step 4: Check
Step 5: Store
NOTE
•Loud test sounds may be played during Audyssey MultEQ automatic speaker setup. This is part of normal operation. If there is background noise in room, these test signals will increase in volume.
•Do not stand between the speakers and setup microphone or allow obstacles in the path while the measurements are being made. This will cause inaccurate readings.
•Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices as measurements may be affected by these sounds.
Cell phones should be placed away from all audio electronics during the measurement process as Radio Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use).
•Operating MASTER VOLUME during the measurements will cancel the measurements.
About the Auto Setup
The Audyssey MultEQ auto setup function detects the presence of each speaker and automatically calculates the speaker size, channel level, distance, and optimal crossover frequency setting. Audyssey MultEQ corrects acoustical distortions within the listening area.
Before starting, connect and position all of your speakers.
Once started, MultEQ will play a series of test tones through each speaker.
If an error message appears during the measurements, check “Error Messages”, take the advised action, then start the measurements again (vpage 24).
b Before starting Auto Setup (v q)
If adjustment to the environment is necessary, set the following items before proceeding.
nFront Speaker
The front speaker to be measured can be selected ahead of time here.
[Selectable items]
A: Output test tone from front speakers A.
B: Output test tone from front speakers B.
A+B : Output test tone from front speakers A and B.
ENGLISH
nAmp Assign | Getting | |
You can use the surround back speaker for | ||
Advanced setting : changes power amplifier assignment. |
| |
channel | Started | |
For details, refer to “Amp Assign” (vpage 31). | ||
|
Step 1 : Speaker Detection |
|
|
|
|
| Connections | |||||||||
F Menu screen F |
|
|
|
|
|
|
|
|
| ||||||
|
|
|
| q |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| w |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| Setup | ||||||
|
|
|
| Audyssey MultEQ |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| Auto Setup |
|
|
| |||||
Step1:Speaker Detection |
|
|
|
|
|
| |||||||||
|
|
|
| Audyssey MultEQ |
|
| |||||||||
| Please place microphone |
|
|
|
|
|
| ||||||||
| Step1:Speaker Detection |
|
| ||||||||||||
| at ear height at |
|
|
|
|
| Front Sp. | Yes |
|
|
| ||||
| main listening position. |
|
|
|
|
|
| Playback | |||||||
|
|
|
|
| Center Sp. | Yes |
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
| Front Sp. | A |
|
|
|
| Subwoofer | Yes |
|
| ||
|
| b |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
| Surround Sp.Yes |
|
| ||||||
|
|
| Amp Assign |
|
|
|
|
|
|
| |||||
|
|
|
| Start |
|
|
|
|
| S.Back Sp. | Yes |
|
| ||
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| 2spkrs |
| |||||
|
|
|
| Cancel |
|
|
|
|
|
|
|
| Remote | ||
|
|
|
|
|
|
|
|
| Next |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| Retry |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
The speaker connection and polarity are detected at the first | |||||||||||||||
| Control | ||||||||||||||
measurement position (main listening position). The following |
| ||||||||||||||
attributes are also determined at this time: “Speaker Size”, “Speaker |
| ||||||||||||||
Distance”, “Channel Level”, “Crossover Frequency”. |
|
|
| ||||||||||||
|
|
| |||||||||||||
q Select “Start 0”, then press o. |
|
|
|
|
| ||||||||||
w Select “Next 0”, then press o. |
|
|
|
|
| ||||||||||
n To cancel Auto Setup |
|
|
|
|
| zone | |||||||||
|
|
|
|
|
| ||||||||||
| Press ui to select “Cancel 0”, then press o. |
|
|
| Information | ||||||||||
• If the result differs from the actual connection status or an error |
| ||||||||||||||
message appears, use i to |
| ||||||||||||||
|
| ||||||||||||||
press o to repeat the measurement. |
|
|
|
|
| Troubleshooting | |||||||||
• If the result still differs from the actual connection status after re- |
| ||||||||||||||
measurement or the error message still appears, it is possible that |
| ||||||||||||||
the speakers are not connected properly. Turn the |
| ||||||||||||||
the speaker connections and repeat the measurement process from |
| ||||||||||||||
the beginning. |
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| ||||||
NOTE |
|
|
|
|
|
|
|
|
|
| Specifications | ||||
Do not change the speaker connections or subwoofer volume after |
| ||||||||||||||
“Step 1”. |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
22