![](/images/backgrounds/264985/264985-3014x1.png)
ENGLISH
External synchronized recordingThe synchronized recording can be use when the
When the CD player’s play button is pressed, a synchronized signal for starting is output from the EXT. SYNC. jack. When the STOP buttons on the CD player is pressed, a synchronized signal for stopping is output from the EXT. SYNC. jack.
•Refer to figure 2 to connect the equipment.
•Use a single RCA cable to connect the units’ EXT. SYNC. OUT jacks with the units’ EXT. SYNC. IN jacks.
✽Set the infrared remote sensors of all the units to “OFF” when using this function. Also set the same infrared remote control codes for all the units. (Refer to “PRESET FUNCTIONS AND OPERATIONS” (See page 14).) Failure to make these settings could result in malfunction.
1.Load the CD into
2.Set the reverse mode and Dolby NR of all decks.
3.Adjust the twin recording level of
4.Press the Twin recording button of
5.Press the PLAY (1) button y of
NOTE:
•Use tapes of the same times (lengths) as far as possible.
6.Press the STOP (2) button u of the
Figure 2
L
R
R
L
11BEFORE SWITCHING OFF THE POWER
When you have finished using the CD player, before switching off the power be sure that the disc holder has been closed with the OPEN/CLOSE (5) button.
CAUTION:
• Do not forcibly close the disc holder when the power is off. It may damage the unit when it is transported.
12PRESET FUNCTIONS AND OPERATIONS
(1)List of Preset Functions•Functions can be preset using the buttons on the front panel. These presettings are stored in a permanent memory, so they are not cleared even when the power is turned off.
•The functions shown on the table below can be preset. Set the functions according to the usage purpose to efficiently achieve even higher quality playback.
•One of the preset functions can be used to display information on this set (microprocessor version).
Preset function type | Description | Set upon shipment | No. | |
from factory | ||||
|
|
| ||
|
|
|
| |
Preset type | Selection of preset type. | Preset Type 1 | 1 | |
|
|
|
| |
Finish mode | Setting of operation when playback ends. | Finish Next | 2 | |
|
|
|
| |
Power on mode | Setting of operation when power is turned on. | Power On Standby | 3 | |
|
|
|
| |
Auto cue | Setting of whether or not to perform the auto cue | CueDet. | 4 | |
| operation and the audio startup level. |
|
| |
Auto stop | Setting of whether or not to automatically stop the servo | Sleep 30min | 5 | |
| functions. |
|
| |
Program 1 | Setting of whether or not to play program 1. | Program 1 OFF | 6 | |
|
|
|
| |
Program 2 | Setting of whether or not to play program 2. | Program 2 OFF | 7 | |
|
|
|
| |
Program 3 | Setting of whether or not to play program 3. | Program 3 OFF | 8 | |
|
|
|
| |
End monitor | Setting of whether or not to use the end monitor function | End Mon. 10 s | 9 | |
| and monitor time setting. |
|
| |
E.O.M. | Setting of whether or not to display the EOM and display | E.O.M. 10 s | 10 | |
| time setting. |
|
| |
Next track standby | Setting of whether or not to standby at the next track | Next Stb. OFF | 11 | |
| when the CUE button is pressed during playback. |
|
| |
Next Track Reserve | Setting of operation when select knob is turned during | Reserve. OFF | 12 | |
| playback. |
|
| |
Play speed | Standard playing speed setting. | Normal Speed | 13 | |
|
|
|
| |
Delay start | Delay start time setting. | Delay OFF | 14 | |
|
|
|
| |
Panel lock | Selection of whether or not to enable the panel buttons. | Panel OFF | 15 | |
|
|
|
| |
Play lock | Selection of whether or not to inhibit the panel switches | Play Lock OFF | 16 | |
| during playback. |
|
| |
Eject lock | Selection of whether or not to lock ejecting during | Eject OFF | 17 | |
| playback. |
|
| |
Time mode | Setting of play mode when power is turned on. | Time REMAIN | 18 | |
|
|
|
| |
Frame display | Selection of whether or not to display frames. | FR Disp ON | 19 | |
|
|
|
| |
Text display | Selection of time or text display. | Text OFF | 20 | |
|
|
|
|
14