INSTALLATION

Continued

3.Assemble trim kit. See Assembling Trim, page 11.

4.Place trim on the shoulder screws located on the side and top of the fireplace. Firmly snap the trim over the shoulder screws on fireplace (see Figure 13).

5.Place mantel base close to wall in desired fireplace location.

6.Install gas line. See Connecting To Gas Sup- ply, page 15

7.Carefully place fireplace on mantel base and center left to right. Check for gas leaks. See Checking Gas Connections, page 17.

8.Refer to instructions provided with the mantel for permanent attachment to wall.

9.Slide mantel around fireplace. Be careful not to damage wall or mantel.

10.Adjust assembly to remove any gaps. From back side of fireplace, attach two 2" wood screws through base mounting blocks at- tached to bottom sides of mantel into base (see instructions provided with mantel).

11.Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. See Figure 12 for screw hole location.

Mantel

Screw

Location

Figure 12 - Removing Hood

Shoulder

Screws

Assembled

Trim

Figure 13 - Attaching Trim to Fireplace

INSTALLING BLOWER ASSEMBLY GA3450T

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and danger- ous operation.

CAUTION: Verify proper op- eration after servicing.

Note: If you are using a mantel with your heater, use the following instructions. If your heater is built-in, see For Built-In Installation on page 14.

1.Screen and hood should be removed from fireplace (see page 11). Remove log set and set aside.

2.Install snap bushings found in hardware kit into both holes in rear of blower control shield (see Figure 14).

3.Make sure the wire harness is firmly con- nected to the terminals on the blower bracket assembly.

4.Note the wire locations on back of AUTO/ OFF/ON switch. Carefully remove red wire from the AUTO terminal and blue wire from the ON terminal. Black wire can remain on the middle or OFF terminal (see Figure 15, page 13).

5.Carefully disconnect green and white wires from power cord harness at their insulated connectors.

6.In top of the heater cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly. Attach blower bracket as- sembly to the outer casing with 4 - #10 screws provided (see Figure 15, page 13).

7.Route the wire harness through the hole to the left side of heat deflector. Pull wire harness through lower opening to the left of the blower control shield. (see Figure 15, page 13).

Blower

 

Control

 

Shield

Snap

 

 

Bushing

Figure 14 - Installing Snap Bushings

12

www.desatech.com

113897-01A

Page 12
Image 12
Desa CF26PRA, CF26NRA installation manual Installing Blower Assembly GA3450T, Removing Hood

CF26NRA, CF26PRA specifications

Desa CF26PRA and CF26NRA are highly regarded heating appliances designed for efficient and reliable home heating solutions. These units are part of Desa's comprehensive lineup, known for their innovative technology and user-friendly features. Both models are distinct yet share a common commitment to optimizing warmth and comfort in residential spaces.

One of the main features of the CF26PRA and CF26NRA is their impressive heating capacity. These heaters are engineered to deliver significant BTUs, ensuring that even large rooms are heated rapidly and evenly. Both models utilize a forced air distribution system that effectively circulates warmth throughout the living area, eliminating cold spots and providing a consistent, cozy environment.

In terms of design, the CF26PRA and CF26NRA are visually appealing with modern aesthetics that blend seamlessly into various décors. Their compact size allows for flexible placement, whether freestanding or wall-mounted, making them an ideal choice for any room in the home, including living rooms, basements, or even workshops.

Incorporating advanced technologies, these models are equipped with electronic ignition systems, which eliminate the need for manual lighting, ensuring ease of use. Their adjustable thermostat allows homeowners to set the preferred temperature, automatically regulating heat output to maintain comfort while optimizing energy efficiency.

Both the CF26PRA and CF26NRA are constructed with durable materials that enhance their longevity and performance. This robust build is paired with safety features like automatic shut-off and flame failure protection, providing peace of mind for users, particularly in homes with children or pets.

Energy efficiency is another hallmark of these models. They are designed to consume minimal fuel while maximizing output, which helps in reducing monthly heating costs without sacrificing comfort. The CF26NRA, specifically, features an enhanced combustion system, further improving fuel efficiency and lowering emissions.

In conclusion, Desa CF26PRA and CF26NRA are excellent choices for anyone seeking reliable, efficient, and stylish heating solutions. With their user-friendly features, advanced technology, and strong performance characteristics, both models represent a solid investment for maintaining a warm and inviting home during cold weather months. Whether you're upgrading your heating system or looking for a supplemental heater, these models will meet and exceed expectations, keeping every corner of your home comfortably warm.