OWNER’S MANUAL
INSTALLING TO WALL
Continued
INSTALLING HEATER TO WALL
Mounting Bracket
The mounting bracket is located on back panel of heater. It has been taped there for shipping. Remove mounting bracket from back panel.
Mounting
Bracket
Figure 5 - Mounting Bracket Location
Removing Front Panel Of Heater
1.Remove two screws near bottom cor- ners of front panel.
2.Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4".
3.Pull bottom of front panel forward, then down.
4.Remove cardboard packing from grill and glass (CGP20[L]) or heat shield (RP30D).
Figure 6 - Removing Front Panel Of Heater
Methods For Attaching Mounting Bracket To Wall
Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes are 16 inches apart from their centers. Attach mounting bracket to wall in one of two ways.
1.Attaching to wall stud
2.Attaching to wall anchor
Attaching to wall stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.
Attaching to wall anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).
Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.
Marking Screw Locations
1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.
2.Mark screw locations on wall (see Fig- ure 7).
WARNING: Maintain minimum clearances shown in Figure 7. If you can, provide greater clear- ances from floor and joining wall.
Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.
3.Remove tape and mounting bracket from wall.
11" | 16" |
Min. |
|
AdjoiningWall |
| Only Insert Mounting |
| 32 1/2" | |
|
| Screws Through Last | |||
|
| Min. | |||
|
| Hole On Each End |
| ||
|
|
|
| ||
|
| Floor |
|
| |
|
| RP30D |
|
| |
| 7 1/4" | 16" |
|
| |
| Min. |
|
|
| |
AdjoiningWall | Only Insert Mounting | 18 3/4" | |||
Screws Through Last | |||||
| Min. | ||||
|
| Hole On Each End |
| ||
|
|
|
| ||
Floor
CGP20(L)
Figure 7 - Mounting Bracket Clearances
Attaching Mounting Bracket To Wall
Note: Wall anchors, mounting screws, and spacers are in hardware package. The hard- ware package is provided with heater.
Attaching to wall stud method
For attaching mounting bracket to wall studs
1.Drill holes at marked locations using 9/64" drill bit.
2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.
3.Insert mounting screws through bracket and into wall studs.
4.Tighten screws until mounting bracket is firmly fastened to wall studs.
Attaching to wall anchor method
For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)
1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.
2.Fold wall anchor as shown in Figure 8.
Figure 8 - Folding Anchor
3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.
4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings.
MPORTANT: Do not hammer key!
For thick walls (over 1/2" thick) or solid walls, do not pop open wings.
Figure 9 - Popping Open Anchor Wings For Thin Walls
5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.
6.Insert mounting screws through bracket and into wall anchors.
7.Tighten screws until mounting bracket is firmly fastened to wall.
Continued
103569 | 7 |
