SAFETY INFORMATION PRODUCT IDENTIFICATION
3
SAFETY INFORMATION
Continued
5. | This stove reaches high temperatures. Keep children and adults |
| away from hot surfaces to avoid burns or clothing ignition. Stove |
| will remain hot for a time after |
| cool before touching. |
6. | Carefully supervise young children when they are in the room |
| with stove. |
7. | Do not modify this stove or burner system under any circum- |
| stances. Any parts removed for servicing must be replaced prior |
| to operating burner system. |
8. | Turn burner system off and let cool before servicing, installing, |
| or repairing. Only a qualified service person should install, ser- |
| vice, or repair this stove or burner system. Have stove and burner |
| system inspected annually by a qualified service person. |
9. | You must keep control compartments, burners, and circulating air |
| passages clean. More frequent cleaning may be needed due to |
| excessive lint and dust from carpeting, bedding material, pet hair, |
| etc. Turn off the gas valve and pilot light before cleaning stove or |
| burner system. |
10. | Have venting system inspected annually by a qualified service |
| person. If needed, have venting system cleaned or repaired. |
| See Cleaning and Maintenance, page 22. |
11. | Keep the area around your stove clear of combustible materi- |
| als, gasoline, and other flammable vapor and liquids. Do not |
| run burner system where these are used or stored. Do not place |
| items such as clothing or decorations on or around stove. |
12. | Do not use this stove to cook food or burn paper or other objects. |
13. | Never place anything on top of stove. |
14. | Do not use any solid fuels (wood, coal, paper, cardboard, etc.) |
| in this burner system. Use only the gas type indicated on burner |
20.Do not use a blower insert, heat exchanger insert, or other ac- cessory not approved for use with this stove.
21.Do not operate burner system with glass door removed, cracked, or broken.
22.This heater must be properly connected to a vent system. This heater is equipped with a vent safety shutoff system.
PRODUCT IDENTIFICATION
Cast Iron
Stove Body
Log Set
Piezo Ignitor | Control Valve |
Vent Opening | Cast Iron |
Stove Body | |
Rear |
|
Cover |
|
| system nameplate. |
15. | This appliance, when installed, must be electrically grounded |
| in accordance with local codes or, in the absence of local codes, |
| with the National Electrical Code, ANSI/NFPA 70, or the Ca- |
| nadian Electrical Code, CSA C22.1. |
16. | Do not obstruct the flow of combustion and ventilation air in |
| any way. Provide adequate clearances around air openings into |
| the combustion chamber along with adequate accessibility |
| clearance for servicing and proper operation. |
17. | Do not install stove with burner system directly on carpeting, |
| vinyl tile, or any combustible material other than wood. The stove |
| must set on a metal or wood panel extending the full width and |
| depth of the stove. |
18. | Do not use stove or burner system if any part has been ex- |
| posed to or under water. Immediately call a qualified service |
| person to arrange for replacement of the unit. |
19. | Do not operate burner system if any log is broken. |
ON/OFF Switch (Other Side)
Blower with
Adjustment Pilot
KnobAssy (Optional
Installation)
| Burner |
| Glass |
| Door |
| Assy |
| Lava |
| Rock |
Grate | Glowing |
Assembly | |
| Embers |
Figure 1 - DESA
Approved DESA Cast Iron Stove Body Models SCIVFC Series
and PSCIVFC Series Only
For morevisit www..com