OWNER’S MANUAL

FIREPLACE INSTALLATION

Continued

INSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1

WARNING: Installation must be done by a qualified installer familiar with low voltage wiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or fire hazard will occur.

1.Open lower door panel. The valve is attached to the underside of the fire- box assembly.

2.Disconnect from the valve the wires running from the ON/OFF switch.

3.Connect one terminal of the wire for the wall thermostat to the THTP termi- nal on the valve. Connect remaining wire terminal to the TH terminal on the valve. Make sure that the wire termi- nals are in the positions on the unit as pictured in Figure 31. If wires are not connected as shown the thermostat will not work.

4.Route the wire to a convenient loca- tion to mount your thermostat (no out- side wall). IMPORTANT: The wire must not exceed 25 feet in length.

The thermostat should be mounted 54" above the floor in a location where there is good air circulation. Avoid heat sources such as lamps, direct sun- light, fireplace, or heat and air condi- tioning ducts.

5.Gently remove the cover of the ther- mostat from the base. Grasp the sides of the cover firmly and pull to separate from the base.

6.Feed the electrical wires through the rectangular slots (from the back) on each side of the base (see Figure 32).

WARNING: Do not connect this thermostat to a power source. Electrical shock and/or fire hazard will occur.

7.Connect one bare wire end to each ter- minal (“W” and “R”) of the thermostat base (see Figure 33).

8.Install the base to the wall with screws provided with thermostat.

9.Move the temperature adjustment back and forth to insure the bi-metal is free from restrictions.

10.Replace the cover onto the base. (Upon installation, the thermostat must be al- lowed to stabilize at room temperature for a minimum of 30 minutes for proper operation.)

11.Set the temperature adjustment to the desired setting. This thermostat has been electronically calibrated at the factory. No adjustment or leveling is necessary.

Feed wires through rectangular slots

Figure 32 - Back View of Thermostat Base

Terminal "W"

W

Terminal "R"

R

Figure 33 - Thermostat Base Terminal "W" and "R"

To Control

Switch or

Optional

Accessory

Figure 31 - Control Valve Terminals

Continued

 

105500

15

Page 15
Image 15
Desa SBVBN(A), SBVBP(A) installation manual Installing Optional Wall Mounted Thermostat GWMT1, Back View of Thermostat Base

SBVBN(A), SBVBP(A) specifications

Desa SBVBN(A) and SBVBP(A) are innovative solutions in the realm of wireless communication, designed to enhance connectivity and network efficiency. Each model is tailored for specific applications, making them essential tools in modern telecommunications.

One of the primary features of both the SBVBN(A) and SBVBP(A) models is their support for advanced modulation techniques. These modulations allow for higher data rates and improved spectral efficiency, which are critical for congested environments. By employing technologies such as Orthogonal Frequency-Division Multiplexing (OFDM), these systems can deliver superior performance even in challenging conditions.

In terms of connectivity, SBVBN(A) focuses on boosting signal strength over long distances. This is especially vital in rural areas where traditional infrastructure may be lacking. The system can cover expansive regions with minimal signal degradation, ensuring reliable communication. Meanwhile, SBVBP(A) is optimized for high-density urban settings, capable of handling a large number of simultaneous connections without compromising speed or quality.

The integration of artificial intelligence and machine learning technologies is another standout feature. Both models utilize smart algorithms to analyze network traffic in real-time, enabling dynamic adjustments to optimize performance. This capability is crucial in environments where user demand can fluctuate drastically, allowing for adaptive resource allocation and enhanced user experience.

Power efficiency is also a significant characteristic of Desa SBVBN(A) and SBVBP(A). Equipped with energy-saving technologies, these systems minimize power consumption while maximizing output. This not only reduces operational costs but also aligns with global sustainability goals.

Moreover, the systems are designed with scalability in mind. They can be easily integrated into existing infrastructures, providing a seamless upgrade path for telecommunication providers looking to enhance their services without major overhauls.

Security is a top priority for both products. They incorporate advanced encryption protocols and access controls, ensuring that data transmission remains secure and protecting against potential threats.

In summary, Desa SBVBN(A) and SBVBP(A) represent the future of wireless communication, with their focus on advanced modulation, AI integration, energy efficiency, scalability, and security. These features make them ideal solutions for a variety of applications, ranging from rural connectivity to urban high-density environments, thus playing a significant role in bridging the digital divide and fostering enhanced communication worldwide.