Desa SBVBP(A) Operating Fireplace, For Your Safety Read Before Lighting, Lighting Instructions

®

B-VENT FREESTANDING FIREPLACE

OPERATING

FIREPLACE

FOR YOUR SAFETY

READ BEFORE

LIGHTING

WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result caus- ing property damage, personal injury or loss of life.

A. This appliance has a pilot which must

be lighted by hand. When lighting the

pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all

around the appliance area for gas. Be

sure to smell next to the floor because

some gas is heavier than air and will

settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

LIGHTING

INSTRUCTIONS

1.	STOP! Read the safety information
	in column one.
2.	Open lower panel.
3.	Turn ON/OFF switch to “OFF”.
4.	Turn off all electric power to the
	fireplace.
5.	Push in gas control knob slightly and
	turn clockwise	to “OFF”.
6.	Wait five (5) minutes to clear out any
	gas. Then smell for gas, including
	near the floor. If you smell gas,
	STOP! Follow “B” in the safety in-
	formation in column one. If you don't
	smell gas, go to the next step.
7.	The pilot is located by the main
	burner and should not require ac-
	cessing for lighting.
8.	Turn knob on gas control counter-
	clockwise	to “PILOT”.
9.	Push in control knob all the way and

TO TURN OFF GAS

TO APPLIANCE

1.Open lower louver panel.

2a. Set selector switch in the “OFF” position.

2b. If Using Optional Hand-Held Re- mote: Set selector switch in the OFF position to prevent draining battery.

3.Turn off all electrical power to the appliance if service is to be performed.

4.Push in gas control knob slightly and

turn clockwise to “OFF”.

5.Close lower panel.

Shutting Off Burners Only (pilot stays lit)

You may shut off the burners and keep the pilot lit by doing one of the following:

1.Turn control knob clockwise to the PILOT position.

2.Set selector switch in the OFF position.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor's phone. Follow

the gas supplier's instructions.

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

hold. Immediately light the pilot by

repeatedly depressing the piezo

spark ignitor until a flame appears.

Continue to hold for about one (1)

minute after the pilot is lit. Release

knob and it will pop back. Pilot

should remain lit. If it goes out, re-

peat steps 5 through 8.

Variable Control Knob

O	H
L
	I

Gas Control Knob

T	ON
O	OFF
L
I
P

If the knob will not push in or turn

by hand, don't try to repair it, call a

qualified service technician. Force or

attempted repair may result in a fire

or explosion.

D. Do not use this appliance if any part

has been under water. Immediately

call a qualified service technician to

inspect the appliance and to replace

any part of the control system and

any gas control which has been un-

der water.

	• If knob does not pop up when re-
	leased, stop and immediately call your
	service technician or gas supplier.
	• If the pilot will not stay lit after sev-
	eral tries, turn the gas control knob
	to “OFF” and call your service
	technician or gas supplier.
10.	Turn gas control counterclockwise
	to “ON”.
11.	Turn on all electric power to the
	fireplace.
12.	Turn the ON/OFF switch to ON
	position.
13.	This valve is equipped with a HI/LO
	feature. Set fireplace input as desired.
14.	Close lower panel.

Piezo Ignitor

Figure 45 - Control Valve

MANUAL LIGHTING

PROCEDURE

1.Remove glass door (see Removing/ Replacing Glass Door, page 16).

2.Follow steps 1 through 8 under Light- ing Instructions.

3.Depress control knob and light pilot with match.

4.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 10 through 14, column 2.

5.Replace glass door (see Removing/ Replacing Glass Door, page 16).

18 105500