TROUBLESHOOTING

Note: For additional help, visit DESA International’s technical service web site at www.desatech.com.

Note: All troubleshooting items are listed in order of operation.

WARNING: Turn off heater and let cool before servicing. Only a quali- fied service person should service and repair heater.

TROUBLESHOOTING

29

CAUTION: Never use a wire, needle, or similar object to clean pilot. This can damage pilot unit.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed, there is no spark at pilot

1.Ignitor electrode not connected to igni- tor cable

2.Ignitor cable pinched or wet

3.Piezo ignitor nut is loose

4.Broken ignitor cable

5.Bad piezo ignitor

6.Ignitor electrode broken

7.Ignitor electrode positioned wrong

1.Reconnect ignitor cable

2.Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry

3.Tighten nut holding piezo ignitor. Nut is located behind the mounting bracket

4.Replace ignitor cable

5.Replace piezo ignitor

6.Replace pilot assembly

7.Replace pilot assembly

When ignitor button is pressed, there is spark at pilot but no ignition

1.Gas supply turned off or equipment shutoff valve closed

2.Gas control knob not in PILOT position

3.Gas control knob not pressed in while in PILOT position

4.Air in gas lines when installed

5.Depleted gas supply (propane/LP models only)

6.Pilot is clogged

7.Gas regulator setting is not correct

1.Turn on gas supply or open equipment shutoff valve

2.Turn gas control knob to PILOT position

3.Press in gas control knob while in PILOT position

4.Continue holding down control knob. Repeat igniting operation until air is re- moved

5.Contact local propane/LP gas company

6.Clean pilot (see Cleaning and Mainte- nance, page 28) or replace pilot assembly

7.Replace gas control

Pilot lights but flame goes out when control knob is released

1.Gas control knob not fully pressed in

2.Gas control knob not pressed in long enough

3.Equipment shutoff valve not fully open

4.Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This prob- lem could be caused by one or both of the following:

A)Low gas pressure

B)Dirty or partially clogged pilot

5.Thermocouple connection loose at con- trol valve

6.Thermocouple damaged

7.Control valve damaged

1.Press in gas control knob fully

2.After pilot lights, keep gas control knob pressed in 30 seconds

3.Fully open equipment shutoff valve

4.A) Contact local natural or propane/LP gas company

B)Clean pilot (see Cleaning and Maintenance, page 28) or replace pi- lot assembly

5.Hand tighten until snug, then tighten 1/4 turn more

6.Replace thermocouple

7.Replace control valve

For morevisit www..com

108661

Page 29
Image 29
Desa T32N, T36N, T32P, T36P installation manual Troubleshooting, Observed Problem Possible Cause

T32N, T36N, T32P, T36P specifications

Desa T32N, T36N, T32P, and T36P are prominent technologies that represent the cutting-edge advancements in the field of telecommunications and data transmission. These systems are crucial for a variety of applications, including telecommunications networks, data centers, and various other technological infrastructures that require high-speed and reliable data transfer capabilities.

Starting with the T32N and T36N models, these systems are characterized by their exceptional bandwidth capacity and high processing speeds. They are designed to cater to the growing demand for faster internet connections and efficient data handling. One of the main features of these models is their ability to support multiple channels simultaneously, allowing for numerous data streams to be processed at once. This is particularly beneficial for environments where data traffic is high, such as urban areas and corporate networks. The T32N and T36N utilize advanced modulation techniques to enhance signal quality, effectively minimizing interference and increasing overall throughput.

On the other hand, the T32P and T36P models are specially engineered for optimal performance under varying network conditions. These models are equipped with adaptive technologies that automatically adjust to network demands, ensuring consistent data delivery even during peak usage periods. The main trait of these systems is their resilience; they are built to withstand fluctuations in data traffic and environmental factors, making them suitable for deployment in diverse settings, from rural areas to densely populated cities.

All four models leverage state-of-the-art technologies such as MIMO (Multiple Input Multiple Output) and beamforming to maximize efficiency and coverage. MIMO technology allows these systems to transmit and receive multiple data streams simultaneously, significantly boosting the data rate and overall system capacity. Beamforming enhances the directivity of the signal, focusing the transmission toward specific receivers, which not only improves signal strength but also reduces interference with other devices.

Another noteworthy characteristic of the Desa T32N, T36N, T32P, and T36P family is their compatibility with a wide range of existing technologies and infrastructures. This interoperability allows for seamless integration into current systems, facilitating upgrades without the need for complete overhauls. As the landscape of technology continues to evolve, these models stand out for their robust features and adaptive capabilities, solidifying their position as essential tools in the advancement of telecommunications and data transfer solutions.