Fireplace Installation
Continued
6.Place log #6 (left log) onto left pin of front log (#2) and the smooth surface of rear log (#3) as shown in Figure 49. Make sure it is seated properly.
7.For (V)V42A series only, place log #7 onto right pin of top log (#5) as shown in Figure 49. Make sure it is seated properly.
8.Place lava rock along sides and front of firebox bottom in areas that are visible only. It is not necessary to use all of the lava rock provided.
NOTICE: Do not put lava rock on burner or under burner. Placing lava rock on burner will cause performance problems.
9.Pull ember material apart into pieces no larger than a dime. Place these pieces loosely and sparingly directly onto the exposed section of the front burner and along space between burner and grate prongs (see Figure 50). This will create the glowing ember appearance as flame touches the ember mate- rial. Do not block air slots by using too much ember material in one area. It is not necessary to use all of the ember material provided.
10.Close glass door, lock door latches, replace screen and close louvers (see Removing/Replacing Glass Door, steps 5 through 7 on page 19).
WARNING: The glass door must be securely in place before running this fireplace. Do not run this fireplace if glass is missing or broken.
6 | 7 |
|
42" Series
Only
Figure 49 - Installing Log No. 6 and No. 7
Ember Material
Figure 50 - Placing Ember Material on Burner
Operating Fireplace
for your safety read
before lighting
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•Do not try to light any appliance.
•Do not touch any electric switch; do not use any phone in your building.
•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D.Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.
Lighting
instructions
1.STOP! Read the safety information above.
2.Open lower louver panel.
3.Disconnect wire that runs from TH to TPTH from control valve.
4.Turn off all electric power to the fireplace.
5.Push in gas control knob slightly and turn clockwise 
to OFF.
6.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow
“B” in the safety information above. If you don't smell gas, go to the next step.
7.The pilot is located by the main burner and should not require accessing for lighting.
8.Turn gas control knob counterclockwise 
to PILOT.
9.Push in gas control knob all the way and hold. Immediately light the pilot by repeatedly depressing the piezo spark ignitor until a flame appears. Continue to hold for about one (1) minute after the pilot is lit. Release gas control knob and it will pop back. Pilot should remain lit. If it goes out, repeat steps 5 through 8.
•If gas control knob does not pop up when released, stop and immediately call your service technician or gas supplier.
•If the pilot will not stay lit after several tries, turn the gas control knob to OFF and call your service technician or gas supplier.
10.Reconnect wire that runs from TH to TPTH to control valve.
www.desatech.com | 21 |
