TROUBLESHOOTING
19
TROUBLESHOOTING
Note: For additional help, visit DESA technical service web site at www.desatech.com.
Note: All troubleshooting items are listed in order of operation.
WARNING: �Turn off and un- plug heater and let cool before servicing.Only a qualified service person should service and repair heater.
CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot.This can damage ODS/ pilot unit.
OBSERVED PROBLEM | POSSIBLE CAUSE | REMEDY | |||
|
|
|
|
| |
When ignitor button is pressed, there is no | 1. | Ignitor electrode not connected to ignitor | 1. | Reconnect ignitor cable | |
spark at ODS/pilot |
| cable |
|
|
|
| 2. | Ignitor cable pinched or wet | 2. | Free ignitor cable if pinched by any | |
|
|
|
| metal or tubing. Keep ignitor cable dry | |
| 3. | Piezo ignitor nut is loose | 3. | Tighten nut holding piezo ignitor to base | |
|
|
|
| panel of log set. Nut is located behind | |
|
|
|
| base panel. | |
| 4. | Broken ignitor cable | 4. | Replace ignitor cable | |
| 5. | Bad piezo ignitor | 5. | Replace piezo ignitor | |
| 6. | Ignitor electrode positioned wrong or | 6. | Replace pilot assembly for | |
|
| broken |
| units; Replace ignitor electrode for vari- | |
|
|
|
| able manually controlled units | |
|
|
|
|
|
|
When ignitor button is pressed, there is spark | 1. | Gas supply turned off or equipment | 1. | Turn on gas supply or open equipment | |
at ODS/pilot but no ignition |
| shutoff valve closed |
| shutoff valve | |
| 2. | Control knob not in PILOT position | 2. | Turn control knob to PILOT position | |
| 3. | Control knob not pressed in while in | 3. | Press in control knob while in PILOT | |
|
| PILOT position |
| position | |
| 4. | Air in gas lines when installed | 4. | Continue holding down control knob. | |
|
|
|
| Repeat igniting operation until air is | |
|
|
|
| removed | |
| 5. | Depleted gas supply (propane/LP | 5. | Contact local propane/LP gas company | |
|
| only) |
|
|
|
| 6. | ODS/pilot is clogged | 6. | Clean ODS/pilot (see Cleaning and | |
|
|
|
| Maintenance, page 18) or replace | |
|
|
|
| ODS/pilot assembly | |
| 7. | Gas regulator setting is not correct | 7. | Replace gas regulator | |
|
|
|
|
|
|
ODS/pilot lights but flame goes out when | 1. | Control knob not fully pressed in | 1. | Press in control knob fully | |
control knob is released | 2. | Control knob not pressed in long | 2. | After ODS/pilot lights, keep control | |
|
| enough |
| knob pressed in 30 seconds | |
| 3. | Safety interlock system has been | 3. | Wait one minute for safety interlock sys- | |
|
| triggered |
| tem to reset. Repeat ignition operation | |
| 4. | Equipment shutoff valve not fully open | 4. | Fully open equipment shutoff valve | |
| 5. | Pilot flame not touching thermocouple, | 5. | A) Contact local natural or propane/LP | |
|
| which allows thermocouple to cool, |
| gas company | |
|
| causing pilot flame to go out. This prob- |
|
|
|
|
| lem could be caused by one or both of |
| B) Clean ODS/pilot (see Cleaning and | |
|
| the following: |
| Maintenance, page 18) or replace ODS/ | |
|
| A) Low gas pressure |
| pilot assembly | |
|
| B) Dirty or partially clogged ODS/ |
|
|
|
|
| pilot |
|
|
|
| 6. | Thermocouple connection loose at con- | 6. | Hand tighten until snug, then tighten | |
|
| trol valve |
| 1/4 turn more | |
| 7. | Thermocouple damaged | 7. | Replace pilot assembly | |
| 8. | Control valve damaged | 8. | Replace control valve | |
For more information, visit www.desatech.com
